Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
This specification covers a titanium alloy in the form of bars 6.000 inches (152.40 mm) and under in nominal diameter or least distance between parallel sides, forgings, flash-welded rings 6.000 inches (152.40 mm) and under in thickness, and stock for forging and stock for flash-welded rings of any size (see 8.6).
SAE J1939-75 defines the set of data parameters (SPs) and messages (PGs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPs) and messages (PGs) previously published within this document are published in SAE J1939DA. Applications using the SAE J1939-75 document must refer to SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD with nominal wall thickness 0.015 inch (0.38 mm) and over.
This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This SAE Information Report establishes the Use Cases for communications and customer-focused Key Performance Indicators (KPI) between plug-in electric vehicles (PEVs) and their customers. The Use Case Scenarios define the information to be communicated related to customer convenience features for charge on/off control, charge power curtailment, customer preference settings, charging status, electric vehicle supply equipment (EVSE) availability/access, and electricity usage, plus customer information resulting from conflicts to charging preferences. It also addresses the KPI that can provide a uniform set of metrics to quantitively assess the charging experience. This document only provides the Use Cases that define the communications requirements to enable customers to interact with the PEV and the KPI to optimize their experience with charging a PEV. Specifications such as protocols and physical transfer methods for communicating information are not within the scope of this document.
This top-level document provides a general overview of the SAE J1939 network and describes the subordinate document structure. This document includes definitions of terms and abbreviations which are used among the various SAE J1939 subordinate documents.
This specification covers an aluminum alloy in the form of clad sheet 0.006 to 0.249 inch (0.015 to 6.32 mm), inclusive, in thickness (see 8.6).
This specification covers a premium-aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
This specification covers an aluminum alloy in the form of welding wire (see 8.6).
This specification covers the procedure for ultrasonic inspection of flat, contoured, round, and hollow cylindrical products having a cross-sectional thickness of 0.02 to 0.50 inch (0.5 to 12.7 mm). This specification does not apply to inspection of composite materials.
This specification covers a corrosion-inhibiting, water soluble, modified epoxy primer in liquid form.
This specification covers one type of parchment in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers an aluminum alloy in the form of bars and rods in the sizes and shapes described in 3.3.1 (see 8.7).
This specification defines limits of variation for determining acceptability of the composition of wrought low-alloy and carbon steel parts and material acquired from a producer.
This specification covers a gold-palladium-nickel alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, chips, preforms and a viscous mixture (paste) of the powder in a suitable binder.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a runway deicing and anti-icing product in the form of a solid. Unless otherwise stated, all specifications referenced herein are latest (current) revision.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars 3.00 inches (76.2 mm) and under in nominal diameter, thickness or for hexagons least distance between parallel sides, forgings, flash welded rings 3.00 inches (76.2 mm) and under in nominal radial thickness, and stock of any size for forging, flash welded rings, or heading.
This specification covers one type of paper coated on both sides with polyethylene film in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers the requirements for brush plating of tin-zinc by electrodeposition.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
The SAE Standards for aluminum casting alloys cover a wide range of castings for general and special use, but do not include all the alloys in commercial use. Over the years, aluminum alloys have been identified by many numbering systems as shown in Table 1. Presently, SAE is recommending the use of the UNS Numbering System to identify these materials. The castings are made principally by sand cast, permanent mold, or die cast methods; however, shell molding, investment casting, plaster cast, and other less common foundry methods may also be used. If the alloys listed do not have the desired characteristics, it is recommended that the manufacturers of aluminum castings be consulted.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
Powder metal (P/M) parts are manufactured by pressing metal powders to the required shape in a precision die and sintering to produce metallurgical bonds between the particles, thus generating the appropriate mechanical properties. The shape and mechanical properties of the part may be subsequently modified by repressing or by conventional methods such. as machining and/or heat treating. While powder metallurgy embraces a number of fields wherein metal powders may be used as raw materials, this standard is concerned primarily with information relating to mechanical components and bearings produced from iron-base materials.
This SAE Information Report provides a uniform means of designating wrought steels during a period of usage prior to the time they meet the requirements for SAE standard steel designation. The numbers consist of the prefix PS1 followed by a sequential number starting with 1. A number once assigned is never assigned to any other composition. A PS number may be obtained for steel composition by submitting a written request to SAE Staff, indicating the chemical composition and other pertinent characteristics of the material. If the request is approved according to established procedures, SAE Staff will assign a PS number to the grade. This number will remain in effect until the grade meets the requirements for an SAE standard steel or the grade is discontinued according to established procedures. Table 1 is a listing of the chemical composition limits of potential standard steels which were considered active on the date of the last survey prior to the date of this report. These ladle
Items per page:
50
1 – 50 of 215951