Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Aerospace Standard (AS) establishes the general requirements for a miniature probe type self-sealing, self-aligning, non-locking coupling intended for aerospace liquid cooling systems. The AS5072/slash sheets define the specific performance and dimensional requirements.
This specification covers one type of copper-beryllium alloy in the form of sheet and strip up to 0.188 inch (4.78 mm) in nominal thickness (see 8.7).
This specification covers a silicone-rubber-remover compound in the form of a liquid supplied as a ready-to-use product.
This specification covers a polishing compound for aircraft metals in the form of a liquid or paste.
This specification covers one strength and one weave of mercerized cotton cloth known as "airplane cloth."
This SAE Aerospace Standard (AS) describes the test methods to determine the flammability performance and capability to control the passage of, and effects from, fire on aircraft firewall sealing compounds. The methods are based on requirements of FAR Part 25, Sections 25.865, 25.867, 25.1191, and 25.1193 and may be used to demonstrate compliance with the requirements established by FAA AC 20-135. This standard shall be used in conjunction with applicable material specifications.
This document recommends criteria for the design and installation of flight crew rest facilities (FCRF) on transport category aircraft when operations with an augmented flight crew are performed. NOTE: Within this ARP, the term “must” will indicate items required for compliance with outside known government regulations, especially 14 CFR Part 117. “Shall” describes sections which are required if this ARP is used as a means of compliance. The term “should” will indicate optional requirements, preferences, and recommendations of the approving SAE committee. Wherever noted and bracketed as [FAA] or [EASA], this document includes agency regulations for reference that are not otherwise evaluated herein.
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length.
This SAE Standard provides test procedures, performance requirements, design guidelines, and installation guidelines for snowmobile stop lamp.
This SAE Standard describes a uniform method to calculate and specify travel performance characteristics of hydraulic excavators, material handlers, knuckle boom log loaders, delimbers, feller bunchers, harvesters, processors, and other knuckle boom material handlers. It establishes definitions and specifies machine conditions for calculations and tests. This document applies to crawler mounted machines such as hydraulic excavators as defined in SAE J/ISO 6165 and ISO 7135, and knuckle boom log loaders as defined in SAE J1209 and SAE J2055. This document also applies to certain forestry equipment defined in SAE J1209 and ISO 6814 that have crawler mountings such as delimbers, feller bunchers, harvesters, and processors. Included in the definition of hydraulic excavators are also front shovel, clamshell, and telescoping boom excavators.
This SAE Standard is equivalent to ISO Standard 362 - 1997 except for the differences detailed in Appendix A, and includes the modifications adopted by WP 29 in ECE R51 Revision 1 and EEC 92/97 and EEC 96/20. This document specifies an engineering method for measuring the noise emitted by accelerating highway vehicles of all types (except motorcycles) in intermediate gears with full utilization of the available engine power. The method is designed to meet the requirements of simplicity and reproducibility of results under realistic vehicle operating conditions. Measurements relate to operating conditions of the vehicle which give the highest noise level consistent with urban driving and which lead to reproducible noise emissions. Therefore, an acceleration test at full throttle from a stated engine or vehicle speed is specified. The test method calls for an acoustical environment which can only be obtained in an extensive open space. Such conditions can usually be provided for: a
This SAE Standard provides test procedures, requirements, and guidelines for a parking lamp.
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal directional drilling (HDD) machines as defined by ISO 21467:2023.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 4 inches (102 mm) and under in nominal thickness.
This Aerospace Information Report (AIR) is a historical technical record describing procedures, required continuous sampling conditions, and instrumentation for the measurement of non-volatile particle number and mass concentrations from the exhaust of aircraft gas turbine engines. Procedures are included to calculate sampling loss performance. This AIR is not intended for in-flight testing, nor does it apply to engine operating in the afterburning mode. This Aerospace Information Report is a historical technical record of the initial document detailing the measurement of non-volatile particle emissions at the exit plane of aircraft gas turbine engines. This methodology was adopted by ICAO into Annex 16 Vol II and updated into Aerospace Recommended Practice ARP6320. Future updates of this document may include explanations of the reasoning and assumptions used to develop this measurement methodology.
This document recommends criteria and requirements for a flight management system (FMS) for transport aircraft. The FMS shall provide the functions of lateral navigation, vertical navigation, and performance management and may include time of arrival control. The FMS design shall take human factors considerations into account to produce a fault tolerant system.
This document recommends criteria for Airborne Windshear Systems, including operational objectives, characteristics, and functional requirements. The recommendations in this document apply to transport aircraft, and describe the operational objectives of windshear alerting systems, situational displays, guidance systems, and avoidance/ detection systems.
This specification covers a coating consisting of tungsten disulfide without binders and does not require a curing process.
This SAE Standard specifies test methods and general requirements for the determination of the electrical characteristic data of alternators for road vehicles. It applies to alternators, cooled according to manufacturer’s instructions, mounted on internal combustion engines. This document attempts to follow ISO 8854, dated 1988. ISO 8854 has been modified herein to reflect local market requirements and historical precedent.
This SAE Standard establishes a test method and a definition for disclosing the suction air volume performance of self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
Items per page:
50
1 – 50 of 215826