Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This SAE Surface Vehicle Technical Information Report, SAE J2836/4, establishes diagnostic use cases between plug-in electric vehicles (PEV) and the electric vehicle supply equipment (EVSE). As PEVs are deployed and include both plug-in hybrid electric (PHEV) and battery electric (BEV) vehicle variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document describes the general information required for diagnostics and SAE J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
This document establishes the requirements for screw-on type reattachable couplings for use in low temperature hose assemblies.
This SAE Aerospace Information Report (AIR) outlines a recommended procedure for evaluation of the vibration environment to which the gas turbine engine powerplant is subjected in the helicopter installation. This analysis of engine vibration is normally demonstrated on a one-time basis upon initial certification, or after a major modification, of an engine/helicopter configuration. This AIR deals with linear vibration as measured on the basic case structure of the engine and not, for example, torsional vibration in drive shafting or vibration of a component within the engine such as a compressor or turbine airfoil. In summary, this AIR discusses the engine manufacturer’s "Installation Test Code" aspects of engine vibration and proposes an appropriate measurement method.
This SAE Aerospace Recommended Practice (ARP) identifies and defines a method of measuring those factors affecting installed power available for helicopter powerplants. These factors are installation losses, accessory power extraction, and operational effects. Accurate determination of these factors is vital in the calculation of helicopter performance as described in the RFM. It is intended that the methods presented herein prescribe and define each factor as well as an approach to measuring said factor. Only basic installations of turboshaft engines in helicopters are considered. Although the methods described may apply in principle to other configurations that lead to more complex installation losses, such as an inlet particle separator, inlet barrier filter (with or without a bypass system), or infrared suppressor, specialized or individual techniques may be required in these cases for the determination and definition of engine installation losses. Some rotorcraft may use an
This SAE Aerospace Information Report (AIR) provides an orientation regarding the general technology of chemical oxygen generators to aircraft engineers for assistance in determining whether chemical oxygen generators are an appropriate oxygen supply source for hypoxia protection in a given application and as an aid in specifying such generators. Information regarding the details of design and manufacture of chemical oxygen generators is generally beyond the scope of this document.
This standard covers oronasal type masks which use a continuous flow oxygen supply. Each such mask comprises a facepiece with valves as required, a mask suspension device, a reservoir, or rebreather bag (when used), a length of tubing for connection to the oxygen supply source, and a means for allowing the crew to determine if oxygen is being delivered to the mask. The assembly shall be capable of being stowed suitably to meet the requirements of its intended use.
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
This specification covers a corrosion and heat resistant iron alloy in the form of covered welding electrodes.
This document provides vehicle-level data collection, data analysis, and data verification procedures that may be used to verify that an instrument under test (IUT) satisfies the vehicle-level requirements specified in the SAE International (SAE) J2945/1 standard. For the purposes of this recommended practice, “vehicle-level requirements” primarily consist of those requirements which can be verified external to the vehicle. The IUT for these procedures is a configured dedicated short range communications (DSRC) vehicle-to-vehicle (V2V) device as defined in SAE J2945/1 and is installed on a light vehicle. While the IUT is conceptually separated from the vehicle it is installed on, the tests outlined in this document are primarily vehicle-level so the terms “vehicle” and “IUT” can generally be considered interchangeable. Additionally, non-vehicle-level complementary tests, not included in this document, are required to verify that the entire set of requirements specified in SAE J2945/1
This document provides vehicle-level data collection, data analysis, and data verification procedures that may be used to verify that an instrument under test (IUT) satisfies the vehicle-level requirements specified in SAE J3161/1. For the purposes of this report, “vehicle-level requirements” primarily consist of those requirements which can be verified external to the vehicle. The IUT for these procedures is a configured LTE-V2X vehicle-to-vehicle (V2V) device as defined in SAE J3161/1 and is installed on a vehicle of class 2, 3, 4, or 5. While the IUT is conceptually separated from the vehicle it is installed on, the tests outlined in this document are primarily vehicle level, so the terms “vehicle” and “IUT” can generally be considered interchangeable. Additionally, non-vehicle-level complementary tests, not included in this document, are required to verify that the entire set of requirements specified in SAE J3161/1 is satisfied. This document also includes a Traceability Matrix to
This SAE Aerospace Information Report (AIR) establishes guidelines for evaluating composite electrical connectors and accessories.
This specification covers a two-component adhesive compound, an epoxy resin base and a hardener, in the form of a paste.
This document describes guidelines, methods, and tools used to perform the ongoing safety assessment process for transport airplanes in commercial service (hereafter, termed “airplane”). The process described herein is intended to support an overall safety management program. It is associated with showing compliance with the regulations, and also with assuring a company that it meets its own internal standards. The methods identify a systematic means, but not the only means, to assess ongoing safety. While economic decision-making is an integral part of the safety management process, this document addresses only the ongoing safety assessment process. To put it succinctly, this document addresses the “Is it safe?” part of safety management; it does not address the “How much does it cost?” part of the safety management. This document also does not address any specific organizational structures for accomplishing the safety assessment process. While the nature of the organizational
This SAE Aerospace Information Report (AIR) defines the power spectrum during normal and emergency operations of a twin engine helicopter and thereby postulates suitable power plant rating structures. This document does not address the power requirements for single engine helicopters or those with more than two engines.
This SAE Aerospace Information Report (AIR) presents a review of the types and general characteristics of power sources that may be used to provide the power for gaseous or liquid fluidic control systems. Fluidic definitions, terminology, units and symbols are defined in Reference 2.1.1.
SAE Aerospace Recommended Practice ARP1533 is a procedure for the analysis and evaluation of the measured composition of the exhaust gas from aircraft engines. Measurements of carbon monoxide, carbon dioxide, total hydrocarbon, and the oxides of nitrogen are used to deduce emission indices, fuel-air ratio, combustion efficiency, and exhaust gas thermodynamic properties. The emission indices (EI) are the parameters of critical interest to the engine developers and the atmospheric emissions regulatory agencies because they relate engine performance to environmental impact. While this procedure is intended to guide the analysis and evaluation of the emissions from aircraft gas turbine engines (burning conventional hydrocarbon based liquid fuels), the methodology may be applied to the analysis of the exhaust products of any hydrocarbon/air combustor. Some successful applications include: Aircraft engine combustor development rig tests (aviation jet fueled) Stationary source combustor
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.
This standard establishes the physical item marking requirements for identification purposes for copper and copper-base alloy mill products procured and issued for government activities. Shipment and inspection acceptance markings are not within the scope of this standard.
This document establishes training guidelines applicable to fiber optic technician technical training for individuals involved in the manufacturing, installation, support, integration and testing of fiber optic systems. Applicable personnel include: Managers Engineers Technicians Trainers/Instructors Third Party Maintenance Agencies Quality Assurance Production
Items per page:
50
1 – 50 of 219833