Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This specification covers two types of thickened, water base temporary coating remover in the form of an alkaline liquid.
This slash sheet specifies the operational parameters and characteristics of a particular implementation of the SAE Linear, Token Passing Bus (LTPB) Interface Unit. This slash sheet defines the following: a The physical media interface: This slash sheet specifies the characteristics of the electrical interface to the physical bus media. b The minimum and maximum timing requirements for operation of this implementation of the LTPB. c The data coding used to encode and decode the data for transmission. d The default values to be loaded into the timers of the LTPB interface at power-up prior to intervention by the host processor.
SCOPE IS UNAVAILABLE.
This procurement specification covers rivets fabricated from an aluminum alloy designated as 1100-H14, strain hardened.
The purpose of this SAE Aerospace Information Report (AIR) is to provide management, designers, and operators with information to assist them to decide what type of power train monitoring they desire. This document is to provide assistance in optimizing system complexity, performance, and cost effectiveness. This document covers all power train elements from the point at which energy in a turbine or electric engine is converted via a gear train to mechanical energy for propulsion purposes. The document covers aircraft engine driven transmission and gearbox components, their interfaces, drivetrain shafting, drive shaft hanger bearings, and associated rotating accessories, propellers, and rotor systems as shown in Figure 1. For guidance on monitoring additional engine components not addressed herein (e.g., main shaft bearings and compressor/turbine rotors), refer to ARP1839. This document addresses rotary and fixed wing applications for rotor, turboprop, turbofan, prop fan, and lift fan
This SAE Aerospace Recommended Practice (ARP) document establishes criteria and recommended practices for the use of airborne icing tankers to aid in design and certification of aircraft ice protection systems and components. Several icing tankers are described, along with their capabilities and suggested use. Sample data for these tanker spray systems are included, shown with 14 CFR Parts 25 and 29, Appendix C icing envelopes for continuous maximum and intermittent maximum icing conditions. (Note: In the remainder of this document, the phrase “Appendix C icing envelopes” will be used for brevity.) This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of eight harness satin fabric woven from continuous fiber tow.
This specification covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers transparent flat polycarbonate plastic sheet material suitable for aerospace transparent enclosures requiring excellent optical properties.
This specification covers glass roving impregnated with epoxy resin, the resin being partially processed to a "B" stage condition.
The intent of this specification is for the procurement of the material listed on the QPL and, therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program shall refer to the Quality Assurance section of the base specification, AMS3961. All material qualification and equivalency data has been archived and is available for review upon request. Contact the CMH-17 Secretariat (www.cmh17.org) for additional information.
This SAE Aerospace Information Report (AIR) has been prepared to provide information regarding options for optical control of fluid power actuation devices. It is not intended to establish standards for optical fluid power control, but rather is intended to provide a baseline or foundation from which standards can be developed. It presents and discusses approaches for command and communication with the actuation device via electro-optic means. The development of standards will require industry wide participation and cooperation to ensure interface commonality, reliability, and early reduction to practice. To facilitate such participation, this document provides potential users of the technology a balanced consensus on its present state of development, the prospects for demonstration of production readiness, and a discussion of problem areas within this technology. The intent is to inform the user/designer of the options available for interfacing photonics (optics) to hydraulic power
This specification covers a corrosion and heat resistant steel in the form of welding wire.
This specification covers an iron-nickel-cobalt alloy in the form of sheet, strip, and plate.
This aerospace recommended practice provides a framework and suggested procedures or values for requirements for the design, performance, and test of hydraulically powered servoactuators for use in aircraft flight control systems. The original version of this document was intended for military usage: consequently, the requirements still often reflect such use. However, the basic requirements of this ARP may and should be applicable to commercial usage as well, provided that appropriate considerations are given for the applicable FAR/JAR 25 regulations, hydraulic fluids, and environmental conditions.
This specification covers the specific requirements for aluminum alloy 7178 bar, rod, shapes, tube, and wire produced by extrusion.
The SAE J1939 communications network is developed for use in heavy-duty environments and is suitable for horizontally integrated vehicle industries. The SAE J1939 communications network is applicable for light-duty, medium-duty, and heavy-duty vehicles used on-road or off-road, and for appropriate stationary applications which use vehicle-derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on-highway and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. SAE J1939-71 is the SAE J1939 reference document describing SAE J1939 parameter (SP) and message (PG) definitions, SLOT (standard data encoding) definitions, conventions and notations used to specify the parameter (SP) placement in PG data, conventions for text data parameters, and conventions for PG transmission rates. This document previously contained the majority of the SAE J1939 OSI application layer data parameters and messages for
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, and molded shapes.
This procurement specification covers aircraft-quality solid rivets made from a corrosion- and heat-resistant cobalt alloy of the type identified under the Unified Numbering System as UNS R30605.
Items per page:
50
1 – 50 of 219833