Results
This SAE Standard provides general and dimensional specifications for beaded ends and hose fittings. These connections are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are designed to be used with hoses that are intended to be retained by hose clamps. It is recommended that where step sizes or additional types of fittings are required they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
The purpose of this document is to establish guidelines for determining the critical R134a and R1234yf refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and agricultural tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a and R1234yf refrigerant charge for the HVAC system.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
This SAE Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel, and lubricating oil systems at temperatures between -67 and 450 °F for Class I assemblies, -67 and 275 °F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard (for example, oxygen), shall be subject to the approval of the procuring activity.
This Purchasing Specification (PS), AMS3970/3, specifies the batch release and delivery requirements for carbon fiber fabric epoxy prepreg used for repair. This specification is applicable only when the carbon fiber fabric epoxy prepreg is used as part of the repair system defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials that are qualified against AMS3970 (refer to PRI QPL AMS3970) and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
The intent of this specification is for the procurement of carbon fiber and fiberglass epoxy prepreg products with 350 °F (177 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3) of this base specification, AMS6891.
This Purchasing Specification (PS) AMS3970/4 specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the prepreg system as defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
AMS3970/2B gives specific information about the qualification program for carbon fiber fabric reinforced epoxy structural repair prepreg systems, curing under vacuum at 120 °C (250 °F), and a companion non-structural glass fabric prepreg used for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-curing process with the prepreg for joint solid laminate and sandwich bonding.
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, flash-welded rings up through 4.000 square inches (25.81 cm2) cross section, and stock for flash-welded rings (see 8.6).
This Purchase Specification (PS), AMS3970/5, specifies the batch release and delivery requirements for the companion non-structural glass fiber fabric prepreg. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings under 4 inches (102 mm) in least cross-sectional dimension, and stock of any size for forging or flash-welded rings (see 8.3).
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a premium aircraft-quality corrosion and heat-resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
This test plan defines the requirements of data bus components which comply with the requirements of MIL-STD-1553B, Digital Time Division Command/Response Multiplex Data Bus.
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 7075.
This specification covers the requirements for electrodeposed lead on metal parts.
This specification covers an aluminum alloy in the form of sheet laminated with one or more layers of unidirectional aramid fiber/epoxy prepreg.
This test plan is broken into three major sections for the testing of bus controllers Electrical, Protocol and Noise tests.
The landing gear system is a major and safety critical airframe system that needs to be integrated efficiently to meet the overall aircraft program goals of minimizing the penalties of weight, cost, dispatch reliability and maintenance. As the landing gear system business develops and large-scale teaming arrangements and acquisitions become increasingly common, it may be desirable in some instances to procure an Integrated Landing Gear System. This document provides guidelines and useful references for developing an integrated landing gear system for an aircraft. The document structure is divided into four sections: Landing Gear System Configuration Requirements (Section 3) Landing Gear System Functional Requirements (Section 4) Landing Gear System Integrity Requirements (Section 5) Landing Gear System Program Requirements (Section 6) The landing gear system encompasses all landing gear structural and subsystem elements. Structural elements include shock struts, truck beams, torsion
This specification covers the procedure for ultrasonic inspection of flat, contoured, round, and hollow cylindrical products having a cross-sectional thickness of 0.02 to 0.50 inch (0.5 to 12.7 mm). This specification does not apply to inspection of composite materials.
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of new light-duty trucks and new multipurpose passenger vehicles1 up to and including 2700 kg (6000 lb) GVW and all classes of new passenger cars.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
The turbine-engine inlet flow distortion methodology addressed in this document applies only to the effects of inlet total-pressure distortion. Practices employed to quantify these effects continue to develop and, therefore, periodic updates are anticipated. The effects of other forms of distortion on flow stability and performance, and of any distortion on aeroelastic stability are not addressed. The guidelines can be used as necessary to create a development method to minimize the risk of inlet/engine compatibility problems. The degree to which guidelines for descriptor use, assessment techniques, and testing outlined in this document are applied to a specific program should be consistent with the expected severity of the compatibility problem.
Items per page:
50
1 – 50 of 221684