Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This document describes the major design drivers and considerations when designing a fuel system for a large commercial aircraft. While not intended as a design manual for individual system components, it does refer out to other SAE specifications where more detail on specific components and subsystems is given. It does include examples of a number of calculations associated with sizing of fuel systems, based on those given in NAVAIR 06-5-504, as well as an appendix summarizing basic fluid mechanical equations that are key for fuel system design. It is acknowledged that most of these calculations would today be performed by modeling tools rather than by hand, but it is considered important for the designer to understand the principles. Some details specific to military aircraft are included, but it is intended that later issues of this document will include appendices that give specific considerations for military aircraft, smaller commercial aircraft, and rotorcraft. Features unique
This SAE Aerospace Recommended Practice (ARP) is intended to be used for laser systems mounted on aircraft and propagated into navigable airspace. This does not include lasers onboard aircraft where the beam is contained within an enclosure so that the beam cannot enter into airspace, nor does it include lasers from satellites and spacecraft in outer space. It may be used in conjunction with AS4970, ARP5535, ARP5572, ARP5293, and the ANSI Z136 laser safety standards.
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
SCOPE IS UNAVAILABLE.
This specification covers the requirements for electrodeposited gold plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and foil 0.100 inch (2.54 mm) and under in nominal thickness.
This specification establishes the engineering requirements for the uphill quenching process of aluminum alloy product. Uphill quenching immerses product in liquid nitrogen followed by exposure to a high-pressure/high-velocity steam blast or boiling water.
This specification covers a copper alloy in the form of strip (see 8.6).
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This SAE Standard defines the basic structural elements, and guidance on compilation and management, for a software supportability program. Software supportability considerations include initial design influence and through-life support embracing the operational use, post-delivery modification, and logistics management of software. This document requires that the processes of design, development, selection, and production of software include software supportability considerations, as relevant to particular project needs.
This SAE Recommended Practice provides a taxonomy of terms related to local and regional on-demand and shared mobility services (including ground, aviation, and maritime) and their enabling technologies. Functional definitions for shared modes (both fleet sharing and ride services), services, business models, and mobility applications are defined in this SAE Recommended Practice. This SAE Recommended Practice also provides a taxonomy of related terms and definitions. Though public transport is part of shared mobility, it is not included in this SAE Recommended Practice because its definition is well-established and documented. This document does not provide specifications or otherwise impose requirements on on-demand and shared mobility.
SAE JA6097 (“Using a System Reliability Model to Optimize Maintenance”) shows how to determine which maintenance to perform on a system when that system requires corrective maintenance to achieve the lowest long-term operating cost. While this document may focus on applications to Jet Engines and Aircraft, this methodology could be applied to nearly any type of system. However, it would be most effective for systems that are tightly integrated, where a failure in any part of the system causes the entire system to go off-line, and the process of accessing a failed component can require additional maintenance on other unrelated components.
This SAE Recommended Practice provides a framework for the establishment of a software support concept related to the support and supportability of both custom-developed and Off-the-Shelf (OTS) software. This document complements SAE AIR 5121, JA1004, and JA1005 by providing information needed to understand the support aspects that should be covered by a software supportability program. It should be noted that particular information indicated here should not be considered a complete list of all aspects of the support concept. In particular, the information should not be confused with a list of data elements. This document has general applicability to all sectors of industry and commerce and to all types of equipment that contain software. The target audience for this document includes software acquisition organizations, software logisticians, developers, supporters, and customers. This document is intended to be guidance for business purposes and should be applied when it provides a
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers all aspects in Electrical Wiring Interconnection Systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles, and external pods.
This standard describes the accepted methods used for preparing aerospace sealant test specimens for qualification and quality conformance or acceptance testing. AS5127/1 and AS5127/2 are to be used in conjunction with this document and the applicable AMS specifications.
This standard covers all types of oxygen breathing equipment used in non-military aircraft. It is intended that this standard supplements the requirements of the detail specification or drawings of specific components or assemblies (e.g., regulators, masks, cylinders, etc.). Where a conflict exists between this standard and detail specifications, detail specifications shall take precedence.
This SAE standard establishes the requirement for suppliers to plan a reliability program that satisfies the following three requirements: a The supplier shall ascertain customer requirements b The supplier shall meet customer requirements c The supplier shall assure that customer requirements have been met
This document provides methods and techniques for implementing a reliability program throughout the full life cycle of a software product, whether the product is considered as standalone or part of a system. This document is the companion to the Software Reliability Program Standard [JA1002]. The Standard describes the requirements of a software reliability program to define, meet, and demonstrate assurance of software product reliability using a Plan-Case framework and implemented within the context of a system application. This document has general applicability to all sectors of industry and commerce and to all types of equipment whose functionality is to some degree implemented by software components. It is intended to be guidance for business purposes and should be applied when it provides a value-added basis for the business aspects of development, use, and sustainment of software whose reliability is an important performance parameter. Applicability of specific practices will
This SAE Recommended Practice provides recommended guidelines and best practices for implementing a supportability program to ensure that software is supportable throughout its life cycle. This Implementation Guide is the companion to the Software Supportability Program Standard, SAE JA1004, that describes, within a Plan-Case framework, what software supportability performance requirements are necessary. This document has general applicability to all sectors of industry and commerce and to all types of equipment whose functionality is to some degree implemented via software. It is intended to be guidance for business purposes and should be applied when it provides a value-added basis for the business aspects of development, use, and sustainment of support-critical software. Applicability of specific recommended practices will depend on the support-significance of the software, application domain, and life cycle stage of the software.
This document provides information to help the reader view maintainability in the context of an overall systems engineering effort. The guide defines maintainability, describes its relationship to other disciplines, addresses the basic elements common to sound maintainability programs, and describes the tasks and activities associated with those elements.
This SAE Standard establishes the requirement for suppliers to plan a maintainability program that satisfies the following three requirements: The supplier shall ascertain customer requirements. The supplier shall meet customer requirements. The supplier shall assure that customer requirements have been met.
This SAE Standard provides a framework for the management of software reliability within system reliability requirements. It is based around the Software Reliability Plan and Software Reliability Case and emphasizes the importance of evaluating progress towards meeting software reliability requirements throughout the project life-cycle.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness.
This specification covers a precipitation hardenable corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers one type of organic fiber in the form of roving. The product shall be formed as four ends of 1140 denier (1270 d tex) yarn (AMS3901/3) collected into an approximately parallel arrangement without twist.
This specification covers a corrosion and heat-resistant, vacuum melted, nickel alloy in the form of investment castings.
This specification covers an unfilled polyamide-imide plastic in the form of molded or extruded bar, rod, and shapes. This is designated as Grade 2 material per AMS3670.
This specification covers molded or extruded bar, rod, and shapes produced from a polyamide-imide (PAI) polymer filled with 30% glass fiber. This is designated as Grade 4 material per AMS3670.
This specification covers a nickel in the form of round wire and rectangular ribbon.
This procurement specification covers bolts and screws made from a corrosion and heat resistant, age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286.
This specification covers polyfluoroethylenepropylene in the form of film and sheet 0.020 inch (0.51 mm) and under in nominal thickness.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet and strip up to 0.187 inch (4.75 mm) thick, inclusive, and plate up to 4.000 inches (101.6 mm) thick, inclusive.
This specification covers a corrosion and heat resistant steel in the form of seamless tubing.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers one type of continuous multifilament carbon fibers in the form of a tow or yarn (when twisted). The weight per unit length of the tow or yarn is governed by the filament count which is identified by the supplier's grade or material designation.
This specification covers a corrosion and moderate heat resistant steel in the form of plate.
Items per page:
50
1 – 50 of 219579