Results
This document outlines the evaluation and documentation appropriate when the components of an approved aircraft seat restraint system are replaced or modified by a party other than the Original Equipment Manufacturer of the restraint system.
This specification covers aluminum alloy die castings.
SAE J1939-81 (“Network Management”) defines the processes and messages associated with managing the addresses of applications communicating on an SAE J1939 network. Network management is concerned with the management of addresses and the association of those addresses with an actual function and with the detection and reporting of network related errors. Due to the nature of management of addresses, network management also specifies address selection and address claiming processes, requirements for reaction to brief power outages, and minimum requirements for ECUs on the network.
This SAE Aerospace Standard (AS) defines the requirements for air cycle air conditioning systems used on military air vehicles for cooling, heating, ventilation, and moisture and contamination control. General recommendations for an air conditioning system, which may include an air cycle system as a cooling source, are included in MIL-E-18927E and JSSG-2009. Air cycle air conditioning systems include those components which condition high temperature and high pressure air for delivery to occupied and equipment compartments and to electrical and electronic equipment. This document is applicable to open and closed loop air cycle systems. Definitions are contained in Section 5 of this document.
This SAE Standard covers the mechanical and physical requirements for Compacted Graphite Iron (CGI) castings used in automotive and allied industries. Requirements in this document include: a Tensile Strength b Yield Strength c Elongation d Graphite Morphology
This specification covers several grades of virgin polytetrafluoroethylene (PTFE) resin which may be compounded with pigment and fillers in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This standard covers self-propelled off-road work machines as categorized in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
This specification covers balls made of a low-chromium, high-carbon steel.
This SAE Aerospace Information Report (AIR) applies to landing gear tires and airframe structure for all types and models of civil and military aircraft having tires as part of the landing gear.
This specification covers expanded honeycomb core made of glass cloth impregnated with polyimide resin and supplied in the form of blocks, slices, and ordered shapes.
This recommended practice provides guidance on vehicle Cybersecurity and was created based off of, and expanded on from, existing practices which are being implemented or reported in industry, government and conference papers. The best practices are intended to be flexible, pragmatic, and adaptable in their further application to the vehicle industry as well as to other cyber-physical vehicle systems (e.g., commercial and military vehicles, trucks, busses). Other proprietary Cybersecurity development processes and standards may have been established to support a specific manufacturer’s development processes, and may not be comprehensively represented in this document, however, information contained in this document may help refine existing in-house processes, methods, etc. This recommended practice establishes a set of high-level guiding principles for Cybersecurity as it relates to cyber-physical vehicle systems. This includes: Defining a complete lifecycle process framework that can
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers requirements for material used in electrical insulating heat shrinkable components. The continuous operating temperature of these materials shall range from -75°C to +200°C (-103°F to +392°F). (See 6.1).
This specification covers a titanium alloy in the form of cold drawn wire.
This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 °F. Gaseous service shall be limited to 150 °F.
This SAE Aerospace Recommended Practice (ARP) describes the continuous sampling and analysis of gaseous emissions from aircraft gas turbine engines. The measured gas species include carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), hydrocarbons (HC), and water vapor (H2O). This ARP excludes engine operating procedures and test modes, and is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode. It is recognized that there will probably be major advances in the gas analysis measurement technology. It is not the intent of this ARP to exclude other analysis techniques, but to form the basis of the minimum amount of conventional instruments (those in common industry usage over the last fifteen years) required for the analysis of aircraft engine exhaust. It is the responsibility of the analyst to demonstrate the alternative measurement technology has comparable (or better) performance than the techniques
This specification is a general level subsystem light source specification that establishes test requirements of light emitting diode (LED) components and modules for use in automotive lighting systems. The completed test data from this test specification is intended to be provided to the OEM by the Tier 1 lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved LED module experiences a design, manufacturing, or component change. This document shall be applied to systems that meet the requirements for design, performance, and validation established by government standards. The LED module is defined as the LED devices and any electronics required to properly energize the LEDs using a vehicle electrical power system along with any associated electrical wiring, connectors, and thermal management system. Samples shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
SAE J2534-1_0500 defines the pass-thru interface requirements for the reprogramming of emission related control modules. The SAE J2534-2/X_0500 document set adds extensions to the SAE J2534-1_0500 API (version 05.00) specification so that the API can be used for features not covered in the SAE J2534-1_0500 specification. Together, these features provide a comprehensive framework for a common standard, to protect the software investment of the vehicle OEMs and scan tool manufacturers. There is no required for an SAE J2534-2/X_0500 pass-thru interface to be fully compliant with SAE J2534-1_0500. SAE J2534-2/X_0500 interfaces can implement some or all of the features specified in the SAE J2534-2/X_0500 document set. This document must be used in conjunction with the SAE J2534-2/RE_0500 document.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both weld fitting end and beam seal fitting end connections for use in all types of fluid systems.
The scope of this SAE Aerospace Recommended Practice (ARP) is to establish the procedure for creating titles of aerospace coupling documents generated by SAE Subcommittee G-3A.
This standard only defines interconnect, electrical and logical (functional) requirements for the interface between a Micro Munition and the Host. The physical and mechanical interface between the Micro Munition and Host is undefined. Individual programs will define the relevant requirements for physical and mechanical interfaces in the Interface Control Document (ICD) or system specifications. It is acknowledged that this does not guarantee full interoperability of Interface for Micro Munitions (IMM) interfaces until further standardization is achieved.
The scope of the test method is to provide stakeholders including fluid manufacturers, airport operators, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This simple test is only designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions. It is not possible to set a general acceptance threshold oxidation limit based on this test method because carbon brake stack oxidation is a function of heat sink design and the operating environment.
This SAE Aerospace Standard (AS) establishes the requirements for heat-cured solid film lubricants. For other general or high-temperature applications, refer to AS1701. This document requires qualified products.
This specification presents requirements for thin-walled (inside diameter greater than four times the wall thickness and outside diameter 1/4 inch and larger) corrosion-resistant steel tubing in approximately the 1/8 hard condition, of special quality, suitable for use in high-pressure hydraulic systems.
This specification covers a corrosion and heat-resistant nickel alloy in the form of investment castings.
Items per page:
50
1 – 50 of 219833