Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
SAE J1939-75 defines the set of data parameters (SPs) and messages (PGs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPs) and messages (PGs) previously published within this document are published in SAE J1939DA. Applications using the SAE J1939-75 document must refer to SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
This specification covers a titanium alloy in the form of bars 6.000 inches (152.40 mm) and under in nominal diameter or least distance between parallel sides, forgings, flash-welded rings 6.000 inches (152.40 mm) and under in thickness, and stock for forging and stock for flash-welded rings of any size (see 8.6).
This SAE Information Report establishes the Use Cases for communications and customer-focused Key Performance Indicators (KPI) between plug-in electric vehicles (PEVs) and their customers. The Use Case Scenarios define the information to be communicated related to customer convenience features for charge on/off control, charge power curtailment, customer preference settings, charging status, electric vehicle supply equipment (EVSE) availability/access, and electricity usage, plus customer information resulting from conflicts to charging preferences. It also addresses the KPI that can provide a uniform set of metrics to quantitively assess the charging experience. This document only provides the Use Cases that define the communications requirements to enable customers to interact with the PEV and the KPI to optimize their experience with charging a PEV. Specifications such as protocols and physical transfer methods for communicating information are not within the scope of this document.
This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD with nominal wall thickness 0.015 inch (0.38 mm) and over.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This specification covers electric furnace steel bars and reforging stock of aircraft quality.
This specification covers one width and one strength of nylon webbing.
This specification covers a petroleum-base lubricating oil.
This specification covers one width and one strength of nylon webbing.
This specification covers dielectrically-loaded syntactic foam tiles having a polyimide resin matrix.
This SAE Standard covers the requirements for coatings of high purity aluminum on low alloy steels, high strength steels, corrosion-resisting steels, aluminum alloys and titanium alloys and other materials where appropriate.
This specification covers one strength and weight of nylon fabric in the form of webbing.
This specification and its supplementary detail specifications cover silicon dioxide in the form of a white, amorphous powder.
This specification covers one type of nylon in the form of webbing.
This specification covers a pigmented phenolic-resin-base coating material, filled with polytetrafluoroethylene (PTFE), supplied in kit form.
This specification covers one width and one strength of nylon webbing.
This SAE Standard specifies the requirements for coatings of titanium nitride on non-corrosion resisting and corrosion resisting steels, cast irons and other suitable materials. Standard engineering items such as coated tools, drills and dies would not normally be included.
Items per page:
50
1 – 50 of 215951