Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE J2971 Recommended Practice describes a standard naming convention of aerodynamic devices and technologies used to control aerodynamic forces on trucks and buses weighing more than 10000 pounds (including trailers).
This specification covers the engineering requirements and process for brush plating of silver by electrodeposition. It shall be used, in conjunction with AMS2451, for silver deposits.
This specification covers the specific requirements for aluminum alloy 5083 bar, rod, shapes, tube, and wire produced by extrusion.
This specification covers one type of continuous multifilament carbon fibers in the form of a tow or yarn (when twisted). The weight per unit length of the tow or yarn is governed by the filament count which is identified by the supplier's grade or material designation.
This specification covers the requirements for identification of forgings, including die forgings, hand forgings, and rolled rings.
This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products.
This specification covers virgin, unfilled polytetrafluoroethylene (PTFE) in the form of sheet, manufactured by compression molding and sintering.
This specification covers a paper, coated on both sides and with different release characteristics on each side (i.e., differentially coated), supplied in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers a kraft paper, coated on both sides and with different release characteristics on each side (i.e., differentially coated), supplied in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers a standard fluoroelastomer (FKM) rubber stock in the form of molded test slabs.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers a polyalphaolefin/ester-blend fluid.
This specification covers a standard acrylonitrile butadiene (NBR-L) rubber stock with low acrylonitrile content in the form of molded test slabs.
This specification covers procedures for identifying bars, wire, mechanical tubing, and extrusions of carbon and alloy steels and corrosion and heat-resistant steels and alloys.
This specification covers one type of copper-beryllium alloy in the form of wire.
This SAE Standard identifies contractor activities for planning and conducting HSI as part of procurement activities on Department of Defense (DoD) system acquisition programs. This standard covers HSI processes throughout system design, development, test, production, use, and disposal. Depending on contract phase, type of the program and/or complexity of the program, tailoring of this standard should be applied. Appendix A lists the requrememts (“shall” statements) in this standard along with unique numbers to facilitate tailoring. In addition, Appendix D provides tailoring guidance to better match requirememts in this standard to the DoD’s Adaptive Acquisition Framework pathways. The scope of this standard includes prime and subcontractor HSI activities; it does not include Government HSI activities, which are covered by DoD and service-level regulations and guidelines. HSI programs should use the latest version of standards and handbooks listed below, unless a particular revision is
This specification covers one type of brass in the form of forgings and forging stock.
This specification covers steel in the form of laminated sheet.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers a denatured ethyl alcohol in the form of a liquid.
This specification covers one weight and one weave of novoloid/aramid cloth.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of thermoplastic, polysulfone resin-impregnated carbon fibers in the form of tape or sheet.
This specification covers one strength and weight of nylon fabric in the form of webbing.
This specification covers an unfilled grade of virgin polytetrafluoroethylene (PTFE) resin in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers thermal radiation resistant material in the form of tape with pressure-sensitive adhesive.
This specification covers one type of nylon webbing.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with inorganic pigment in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers one weight and one weave of nylon cloth.
Items per page:
50
1 – 50 of 215930