Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Aerospace Recommended Practice (ARP) establishes the overall component and system function guidelines and minimum performance levels for a TPMS. These guidelines include, but are not limited to: Design recommendations for system components, which: Monitor tire inflation Are located in/on the tire/wheel assembly, landing gear axle, and/or aircraft avionics compartment Recommended performance and safety guidelines for a TPMS.
This specification covers a corrosion-resistant steel in the form of wire.
This document describes the materials, equipment, and processing techniques utilized in the fabrication of polyimide printed wiring boards. Included are recommendations for both double-sided and multilayer boards.
This SAE Aerospace Information Report (AIR) presents preferred design, assembly, and repair practices for sealing of aircraft integral fuel tanks, including rework of applied fuel tank seals. It addresses engineering designs for integral fuel tanks as they are currently found in practice and discusses the most practical and conservative methods for producing a reliable, sealed system. Although this AIR presents practices for sealing of integral fuel tanks, the practices presented within this report are practices that are carried throughout sealing that include both pressure and environmental aircraft sealing. Design preferences for optimum sealing are not within the scope of this document. Such discussions can be found in the United States Air Force (USAF) sponsored report AFWAL-TR-87-3078, “Aircraft Integral Fuel Tank Design Handbook.” Key objectives of the fuel tank sealing process are to produce a sealing plane that is leak-free and corrosion resistant, especially at fastener
This recommended practice describes the physical and chemical characterization techniques for identification of epoxy adhesive and prepreg resin systems in order to verify the chemical formulation, resin B-staging (See 8.1), cure reaction rates, adhesive moisture content, and resin component mix ratios, as necessary to achieve manufacturing and quality producibility and engineering performance.
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
This SAE Recommended Practice provides for common test and verification methods to determine lead acid and nickel metal hydride electric vehicle battery module performance. The document creates the necessary performance tests to determine (a) what the basic performance of EV battery modules is, and (b) if battery modules meet minimum performance specification established by vehicle manufacturers or other purchasers. Specific values for these minimum performance specifications are not a part of this document.
This test can be used to determine the resistance to crocking (color rub-off) of organic trim materials such as fabrics, vinyl coated fabrics, leather, coated fiberboard and carpet. This method is similar to AATCC Method 8 –Colorfastness to Crocking.
This SAE Information Report is intended to be used for routine (or periodic) monitoring of filling station performance. It is not intended to provide process quality control requirements for any portion of the product delivery cycle.
This recommended practice describes the materials, related equipment, and particular processing techniques utilized in process science curing of composite hardware where pressure is imparted specifically to the resin of curing composites. Included as Appendix "A" to this ARP is a discussion of the particular techniques developed for a processing science philosophy which has consistently produced void and porosity-free, large area, thick composite structures.
The following terminology has been generated by the ATA/IATA/SAE Commercial Aircraft Composite Repair Committee (CACRC) and provides terminology for design, fabrication, and repair of composite and bonded metal structures.
This SAE Aerospace Recommended Practice (ARP) describes standard methods of heat application to cure thermosetting resins for commercial aircraft composite repairs. The methods described in this document shall only be used when specified in an approved repair document or with the agreement of the Original Equipment Manufacturer (OEM) or regulatory authority.
This document describes an inspection procedure for detecting, by use of a radiographic opaque tracer and fluoroscopy or radiography methods, flaws which have been produced as the result of cutting, machining, or drilling operations in composite or laminate structures.
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnesses to road vehicles. This document applies to any wiring system which contains one or more circuits operating between 50 V DC or AC RMS and 600 V DC or AC RMS excluding automotive ignition cable.
This document describes a manufacturing method for processing unidirectional carbon fiber/epoxy resin impregnated sheet and tape into multi-ply broadgoods and tape produced on an automated cross-plying machine. Broadgoods or tape of two or more ply configurations may be processed, where ply orientations of 0°, 45°, 90°, and 135° (as examples) may be automatically layed in a programmed sequence. In all configurations, the 0° ply direction is parallel to the length of the broadgoods roll or sheet, or tape.
This document is to be used as a checklist by curriculum developers to create courses or training for critical composite repair, maintenance, and overhaul issues. This document will not take the place of courses or training requirements for specific job roles of a composite repair technician, inspector, or engineer.
This SAE Aerospace Recommended Practice (ARP) provides recommendations for additive manufacturing (AM) designed/repaired aircraft components.
This SAE Standard describes a laboratory test procedure for measuring the vibration damping performance of a system consisting of a damping material bonded to a vibrating cantilevered steel bar. The bar is often called the Oberst bar (named after Dr. H. Oberst) and the test method is often called the Oberst bar test method. Materials for damping treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic (such as aluminum foil) materials. These materials are commonly installed in transportation systems such as ground vehicles, marine products, and aircraft to reduce vibration at resonance, and thus reduce the noise radiation from the vibrating surface. The test method described herein was developed to rank order materials for application on panels using general automotive steel but also may be applicable to other situations or conditions. Damping performance for most materials and systems varies as a function
While there are various types of Fuel Cell architectures being developed, the focus of this document is on Proton Exchange Membrane (PEM) fuel cell stacks and ancillary components for automotive propulsion applications. Within the boundaries of this document are the: Fuel Supply and Storage, Fuel Processor, Fuel Cell Stack, and Balance of Plant, as shown in Figure 1.
Items per page:
50
1 – 50 of 219522