Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This procedure describes a method of measuring the resistance to wet color transfer of materials such as textiles, leather, and composites.
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
The intent of this specification is for the procurement of the material listed on the QPL and, therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of this base specification, AMS6891.
This specification covers a copper-nickel-tin alloy in the form of bars and rods up to 8.500 inches (216 mm), inclusive, in nominal thickness. When tube is ordered to AMS4596, it shall be supplied to AMS4598 (see 8.8).
This specification covers the specific requirements for aluminum alloy 7075 plate and sheet for applications requiring improved exfoliation resistance.
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This specification covers polyurethane (PUR) in the form of two-component sealing compounds.
This specification covers a titanium alloy in the form of bars, wire, forgings up to 4.000 inches (101.60 mm), inclusive, and forging stock.
This specification covers an aluminum alloy in the form of Alclad sheet and plate 0.040 to 1.000 inch, inclusive (1.02 to 25.40 mm, inclusive) in nominal thickness (see 8.5).
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 64 in2 (413 cm2) in the solution and precipitation heat treated (H1075) condition
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm), inclusive, in thickness, supplied in the -T361 temper (see 8.5).
This specification covers a carbon steel in the form of bars up through 3.000 inches (76.20 mm) and forgings and forging stock of any size.
This specification covers a free-machining, corrosion-resistant steel in the form of bars, forgings, and forging stock.
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers engineering requirements for applying tungsten carbide thermal spray coatings to ultrahigh-strength steels (220 ksi and above) utilizing high-velocity oxygen fuel (HVOF) combustion-driven processes and the properties for such coatings. The processes and procedures herein apply only to the properties of the as-deposited coating.
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and rolled rings 4 inches (102 mm) and under in nominal thickness and forging stock of any size (see 8.6).
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 4 inches (102 mm) and under in nominal thickness.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1100) condition, 12 inches (305 mm) and under in nominal diameter, thickness, or, for hexagons, least distance between parallel sides. The aged product may be supplied directly by a producer or by another entity performing the functions of a producer as defined in AS6279. The latter can be accomplished by precipitation heat treatment of solution treated material previously certified to AMS5934. The entity assuming responsibility for the aging operation is designated the producer of AMS5934/H1100.
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness, or for hexagons, least distance between parallel sides in the solution and precipitation heat treated (H1050) condition.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 12 inches (305 mm) and under in nominal diameter, thickness, or, for hexagons, least distance between parallel sides.
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides in the solution and precipitation heat treated (H1150) condition.
This specification covers a coating consisting of tungsten disulfide without binders and does not require a curing process.
This specification covers an ethylene propylene rubber in the form of molded rings, molded compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a coating consisting of finely powdered graphite in a heat-resistant inorganic binder applied to parts.
This SAE Aerospace Standard defines the requirements for establishing a nondestructive inspection (NDI) program for aerospace systems to include but not limited to aircraft structure, aircraft stores (external structures such as antennas, pods, fuel tanks, weapons, radomes, etc.) and missile/rocket structural components when an NDI Program Plan is required by contract. NDI Programs are essential to ensuring NDI processes are implemented to support the lifecycle design requirements of the system and its components. NDI Programs are applicable to all phases of the system life cycle, including acquisition, modification, and sustainment. This standard may also be applicable to mechanical equipment, subsystems, and propulsion systems, but the requirements defined by the NDI Program Plan should be tailored by the contracting agency for such use. An NDI Program Plan shall be developed at the beginning of the technology development phase and shall define all NDI requirements to be adhered to
Items per page:
50
1 – 50 of 216063