Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Aerospace Standard (AS) specifies scarf-cut polytetrafluoroethylene (PTFE) retainers (backup rings) for use in static glands in accordance with AS5857. They are usually for use in hydraulic and pneumatic systems as anti-extrusion devices in conjunction with O-rings and other seals.
This specification covers the requirements for heat-treatment of four classes of steel (See 1.2) and the requirements for furnace equipment, test procedures and information for heat-treating procedures, heat-treating temperatures and material (See 6.3) test procedures. This specification is applicable only to the heat treatment of raw material (See 6.3.1); it does not cover the requirements for the heat treatment of steel parts (See 3.4 and 6.3.2). This specification also describes procedures that, when followed, will produce the desired properties and material qualities within the limitations of the respective alloys tabulated in Tables 1A, 1B, 1C and 1D. Alloys other than those specifically covered herein may be heat treated using all applicable requirements of this specification.
The verification matrix (VM) in this slash sheet is intended for use to establish compliance to AS6174A. This slash sheet is applicable to AS6174A. Nothing in this slash sheet, however, supersedes applicable laws and regulations, unless a specific exemption has been obtained through judicial/legal channels.
This specification covers the specific requirements for 7075 aluminum alloy alclad one side plate and sheet; the general requirements are covered in AMS-QQ-A-250. The plate and sheet covered by this specification shall be an integral composite product consisting of a heat-treatable aluminum alloy (7075) core with a thin layer of an aluminum alloy (7072) anodic to the core bonded to one surface.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
This specification covers a corrosion-resistant nickel-copper alloy in the form of seamless tubing.
This specification covers one type of sintered metal powder in the form of oil-impregnated bearings.
This Aerospace Standard (AS) is to be used as a supplement to SAE AS7112. In addition to the requirements specified in AS7112, the requirements specified herein shall apply to suppliers seeking Nadcap Fluid System accreditation for manufacturing titanium 3AI-2.5V alloy, seamless hydraulic tubing. The corresponding PRI Audit Criteria (AC) is to be applied to ensure the tubing is manufactured to the applicable specification(s) and standard(s).
This document provides information to help the reader view maintainability in the context of an overall systems engineering effort. The guide defines maintainability, describes its relationship to other disciplines, addresses the basic elements common to sound maintainability programs, and describes the tasks and activities associated with those elements.
This specification covers the requirements for one type of tiedown fitting for installation in the floors of aircraft.
This document is intended for use by manufacturers of aircraft, engines and Electronic Engine Controls [EECs] as a component change process and evaluation guideline. Its purpose is to provide an effective means of managing the modification of electronic hardware. The process defined in this document is based upon: an understanding of the electronic component market evolution, e.g., obsolescence; lessons learned from the effects caused by the introduction of electrical component changes in a service fleet environment; industry best practice; and an understanding of the applicable regulations.
This SAE Aerospace Standard (AS) covers the general requirements for the design, manufacture, and test of 28 VDC, 270 VDC, and 115 VAC solid-state power controllers (SSPCs) for use in electrical power systems. SSPCs conforming to this standard are intended for use in controlling the making and breaking of power circuits for electrically operated equipment and devices, and for providing overload and short-circuit protection. Applications that require SSPCs to have a high level of performance in some areas or may be exposed to harsher electrical or environmental conditions are designated as CLASS A. Applications that utilize SSPCs in moderate level of performance or are exposed to a controlled environment are designated as CLASS C. Applicability of both MIL-STD-704 and RTCA DO-160G have been considered when determining the performance standards for the designated classes of SSPCs. To support older aircraft platforms, legacy versions of these specifications were also considered as
The primary objective of this document is to describe the systematic and random measurement uncertainties which may be expected when testing gas turbine engines in a range of different test facilities. The documentation covers a "traditional" method for estimating pretest uncertainties and a "new" method for computing and comparing posttest uncertainties. To determine these posttest uncertainties, data generated during the AGARD Uniform Engine Test Program (UETP) were analyzed and compared to the pretest estimates. The proposed procedure provides a mechanism for determining the expected accuracy of test results obtained from facilities which were not previously cross calibrated. Furthermore, the method can be used to assist in making cost-effective management decisions on the level of validation/cross calibration necessary when bringing a test facility on line. This document is also intended to act as a guide for improving uncertainty analyses in a broad spectrum of related industries
This document defines requirements for digital, command/ response time division multiplexing (data bus) techniques for fiber optic implementation. The concept of operation and information flow on the multiplex data bus and the functional formats to be employed are also defined.
This specification establishes requirements for steel forgings of any shape or form from which finished parts are to be made (See 8.2, 8.3, & 8.4). This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment
This procurement specification covers tubular, blind rivets fabricated from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04405, and of 52 ksi minimum shear strength for self-plugging style rivets.
This SAE Standard applies to spark plug installation sockets of the long length type which are to be used for installing spark plugs of the most commonly used sizes for the North American market.
This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inches (6.35 to 102.0 mm), inclusive, in nominal thickness (see 8.5).
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors, so they will identify smaller refrigerant leaks when servicing all motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning their design or use.
XRF technique for counterfeit detection is applicable to electrical, electronic and electromechanical (EEE) parts as listed in AS6171 General Requirements. In general, the detection technique is meant for use on piece parts prior to assembly on a circuit board or on the parts that are removed from a circuit board. The applicability spans a large swath of active, passive and electromechanical parts. If AS6171/3 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
This SAE Aerospace Standard (AS) defines the requirements for air cycle air conditioning systems used on military air vehicles for cooling, heating, ventilation, and moisture and contamination control. General recommendations for an air conditioning system, which may include an air cycle system as a cooling source, are included in MIL-E-18927E and JSSG-2009. Air cycle air conditioning systems include those components which condition high temperature and high pressure air for delivery to occupied and equipment compartments and to electrical and electronic equipment. This document is applicable to open and closed loop air cycle systems. Definitions are contained in Section 5 of this document.
Items per page:
50
1 – 50 of 222741