Results
This SAE Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel, and lubricating oil systems at temperatures between -67 and 450 °F for Class I assemblies, -67 and 275 °F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard (for example, oxygen), shall be subject to the approval of the procuring activity.
This SAE Standard provides general and dimensional specifications for beaded ends and hose fittings. These connections are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are designed to be used with hoses that are intended to be retained by hose clamps. It is recommended that where step sizes or additional types of fittings are required they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
The purpose of this document is to establish guidelines for determining the critical R134a and R1234yf refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and agricultural tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a and R1234yf refrigerant charge for the HVAC system.
This Purchasing Specification (PS), AMS3970/3, specifies the batch release and delivery requirements for carbon fiber fabric epoxy prepreg used for repair. This specification is applicable only when the carbon fiber fabric epoxy prepreg is used as part of the repair system defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials that are qualified against AMS3970 (refer to PRI QPL AMS3970) and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, flash-welded rings up through 4.000 square inches (25.81 cm2) cross section, and stock for flash-welded rings (see 8.6).
AMS3970/2B gives specific information about the qualification program for carbon fiber fabric reinforced epoxy structural repair prepreg systems, curing under vacuum at 120 °C (250 °F), and a companion non-structural glass fabric prepreg used for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-curing process with the prepreg for joint solid laminate and sandwich bonding.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings under 4 inches (102 mm) in least cross-sectional dimension, and stock of any size for forging or flash-welded rings (see 8.3).
This Purchase Specification (PS), AMS3970/5, specifies the batch release and delivery requirements for the companion non-structural glass fiber fabric prepreg. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This Purchasing Specification (PS) AMS3970/4 specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the prepreg system as defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The intent of this specification is for the procurement of carbon fiber and fiberglass epoxy prepreg products with 350 °F (177 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3) of this base specification, AMS6891.
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This SAE Aerospace Recommended Practice (ARP) identifies the minimum requirements for the testing of insulated electrical wiring for on-aircraft, aeronautical and aerospace applications. The testing requirements defined herein, ensure that a wire fault can be found safely when using a high potential voltage tester (hipot). This test is intended to aid in finding a breach in the wire insulation, and not for the identification of the resistance of the insulation. The test method defined herein is limited to equipment which ia able to control and limit the DC output to 1500 VDC maximum. This type of wire dielectric tester is typically designed to trip on current leakage and not necessarily on arc detection. This test method is solely designed to identify gross/large wire insulation damage or degradation. For additional related information on this topic and related test methods, refer to the documents cited in Section 2. They are intended to aid the reader in the direction of this ARP and
This test method outlines the recommended procedure for performing static axial limit and ultimate load tests on rolling element bearings used in airframe applications. Bearings covered by this document shall be antifriction ball bearings and spherical roller bearings in either annular or rod end configurations.
This specification covers a compressed non-asbestos fiber and acrylonitrile butadiene (NBR) rubber in the form of sheet.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers insulated wire for use in external aircraft antennas.
The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, refer to “Design Practices: Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE-18 (Third Ed.) or AE-29 (Fourth Ed.).
The tow vehicle should be designed for towbarless push-back and/or maintenance towing of regional type aircraft as specified in 1.3. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode. The purpose of this towing procedure is to achieve a safer and faster operation than is possible with conventional towing equipment.
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less-common applications are not covered.
This SAE Recommended Practice applies to a decorative lamp(s) installed on the front of motor vehicles. This lamp(s) is intended only to be decorative and is not to impair the effectiveness of any required lighting device. This recommended practice establishes uniformity in use guidelines for the performance, installation, activation, and switching of a front decorative lamp(s).
Items per page:
50
1 – 50 of 221684