Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
SAE J1939-75 defines the set of data parameters (SPs) and messages (PGs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPs) and messages (PGs) previously published within this document are published in SAE J1939DA. Applications using the SAE J1939-75 document must refer to SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
This specification covers a titanium alloy in the form of bars 6.000 inches (152.40 mm) and under in nominal diameter or least distance between parallel sides, forgings, flash-welded rings 6.000 inches (152.40 mm) and under in thickness, and stock for forging and stock for flash-welded rings of any size (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD with nominal wall thickness 0.015 inch (0.38 mm) and over.
This SAE Information Report establishes the Use Cases for communications and customer-focused Key Performance Indicators (KPI) between plug-in electric vehicles (PEVs) and their customers. The Use Case Scenarios define the information to be communicated related to customer convenience features for charge on/off control, charge power curtailment, customer preference settings, charging status, electric vehicle supply equipment (EVSE) availability/access, and electricity usage, plus customer information resulting from conflicts to charging preferences. It also addresses the KPI that can provide a uniform set of metrics to quantitively assess the charging experience. This document only provides the Use Cases that define the communications requirements to enable customers to interact with the PEV and the KPI to optimize their experience with charging a PEV. Specifications such as protocols and physical transfer methods for communicating information are not within the scope of this document.
This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This top-level document provides a general overview of the SAE J1939 network and describes the subordinate document structure. This document includes definitions of terms and abbreviations which are used among the various SAE J1939 subordinate documents.
This specification covers an aluminum alloy in the form of clad sheet 0.006 to 0.249 inch (0.015 to 6.32 mm), inclusive, in thickness (see 8.6).
This SAE Aerospace Standard (AS) defines the requirements for a polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high pressure, 4000 psi, pneumatic systems for aircraft and missile ground servicing applications at temperatures of -65 to 160 °F.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of sheet 0.250 inch (6.35 mm) and over in thickness, rod, heavy wall tubing, and large molded and machined parts.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of rods, sheets, and molded shapes.
This specification covers an aluminum alloy in the form of hand forgings up to 8 inches (203 mm), inclusive, in nominal thickness and a cross-sectional area not over 256 square inches (1652 cm2) and rolled rings up to 3.5 inches (89 mm), inclusive, in nominal thickness and with an OD to wall thickness ratio of 10:1 or greater (see 8.6).
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
This specification and its supplementary slash specifications establish the requirements for electrodeposition of metals by brush plating.
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
This standard defines requirements for the preparation and execution of the audit process. In addition, it defines the content and composition for the audit reporting of conformity and process effectiveness to the 9100-series standards, the organization's QMS documentation, and customer and statutory/regulatory requirements. The requirements in this standard are additions or represent changes to the requirements and guidelines in the standards for conformity assessment, auditing, and certification as published by ISO/IEC (i.e., ISO/IEC 17000, ISO/IEC 17021-1). When there is conflict with these standards, the requirements of the 9101 standard shall take precedence.
The purpose of this test is to evaluate the axial strength of the nut seat of wheels intended for use on passenger cars, light trucks, and multipurpose vehicles. In addition, a minimum contact area is recommended to ensure enough strength for the rotational force in tightening a nut against the nut seat. While this test ensures the minimum strength of the nut seat, the wheel must also have a degree of flexibility. This flexibility, as well as bolt tension, are important to maintain wheel retention.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish general guidelines for the measurement of static and dynamic characteristic properties of aircraft tires.
Items per page:
50
1 – 50 of 215951