Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine-driven cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depends on the volumetric flow rate, or the pressure rise across the fan, since these two
The techniques outlined in this SAE Recommended Practice were developed as part of an overall program for determining and evaluating fuel consumption of heavy-duty trucks and buses, but it is applicable to off highway vehicles as well. It is recommended that the specific operating conditions be carefully reviewed on the basis of actual installation data. Cooling requirements are affected by all heat exchangers that are cooled by the fan drive system. These may include radiators, condensers, charge air coolers, oil coolers, and others. Because of the variation in size, shape, configuration, and mountings available in cooling fans and fan drive systems, specific test devices have not been included. Using known power/speed relationships for a given fan, this procedure can be used to calculate the fan drive system’s power consumption for cooling systems using the types of drives listed below. This power consumption may then be used in determining engine net power per SAE J1349. For more
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of eight harness satin fabric woven from continuous fiber tow.
This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer
This SAE Recommended Practice establishes uniform laboratory techniques for the continuous and bag-sample measurement of various constituents in the exhaust gas of the gasoline engines installed in passenger cars and light-duty trucks. The report concentrates on the measurement of the following components in exhaust gas: hydrocarbons (HC), carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), and nitrogen oxides (NOx). NOx is the sum of nitric oxide (NO) and nitrogen dioxide (NO2). A complete procedure for testing vehicles may be found in SAE J1094. This document includes the following sections: 1. Scope 2. References 3. Emissions Sampling Systems 4. Emissions Analyzers 5. Data Analysis 6. Associated Test Equipment 7. Test Procedures
Nondestructive tests are those tests which detect factors related to the serviceability or quality of a part or material without limiting its usefulness. Material defects such as surface cracks, laps, pits, internal inclusions, bursts, shrink, seam, hot tears, and composition analysis can be detected. Sometimes their dimensions and exact location can be determined. Such tests can usually be made rapidly. Processing results such as hardness, case depth, wall thickness, ductility, decarburization, cracks, apparent tensile strength, grain size, and lack of weld penetration or fusion may be detectable and measurable. Service results such as corrosion and fatigue cracking may be detected and measured by nondestructive test methods. In many cases, imperfections can be automatically detected so that parts or materials can be classified. The SAE Handbook describes the following nondestructive test methods: SAE J359—Infrared SAE J420—Magnetic Particle SAE J425—Eddy Current SAE J426—Liquid
This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods for specifying thickness tolerances.
This SAE Standard prescribes the procedure for making hardenability tests and recording results on shallow and medium hardening steels, but not deep hardening steels that will normally air harden. Included are procedures using the 25 mm (1 in) standard hardenability end-quench specimen for both medium and shallow hardening steels and subsize method for bars less than 32 mm (1-1/4 in) in diameter. Methods for determining case hardenability of carburized steels are given in SAE J1975. Any hardenability test made under other conditions than those given in this document will not be deemed standard and will be subject to agreement between supplier and user. Whenever check tests are made, all laboratories concerned must arrange to use the same alternate procedure with reference to test specimen and method of grinding for hardness testing. For routine testing of the hardenability of successive heats of steel required to have hardenability within certain limits, it is sufficient to designate
The current document is a part of an effort of the Active Safety Systems Committee, Active Safety Systems Sensors Task Force whose objectives are to: Identify the functionality and performance you could expect from active safety sensors Establish a basic understanding of how sensors work Establish a basic understanding of how sensors can be tested Describe an exemplar set of acceptable requirements and tests associated with each technology Describe the key requirements/functionality for the test targets Describe the unique characteristics of the targets or tests This document will cover items (a) and (b).
This specification covers a titanium alloy in the form of pre-alloyed powder.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
This test plan is broken into three major sections for the testing of bus controllers Electrical, Protocol and Noise tests.
This specification established (1) the common requirements for hydraulic units capable of functioning as starters and as pumps suitable for use in aircraft and missiles and (2) the methods to be used for demonstrating compliance with these requirements.
This test plan defines the requirements of data bus components which comply with the requirements of MIL-STD-1553B, Digital Time Division Command/Response Multiplex Data Bus.
AS95234 includes reverse bayonet coupling, high current electrical connectors that are watertight and principally used in shipboard, ground vehicles and ground support equipment applications at serve voltages from 200 to 3000 Vrms and temperatures between -55 °C and +125 °C (-67 °F and +257 °F). See 6.1.5 for applications details. For aerospace application connectors, refer to AS50881.
This document presents minimum criteria for the design and installation of LED passenger reading light assemblies in commercial aircraft. The use of “shall” in this specification expresses provisions that are binding. Non-mandatory provisions use the term “should.”
The scope of this SAE Recommended Practice is to establish uniform test procedures for passenger cars, to determine whether the system is defined as a defroster or defogger, and to establish minimum performance requirements for each system. A defroster for purposes of this practice is a system which will remove moisture and/or frost from the interior surface of the backlight at −18 °C. A defogger is a system which will remove moisture and/or fog from the interior surface of the backlight at 4 °C. The test procedure is intended to simulate actual conditions by utilizing either a cold room with an appropriate device to introduce air flow over the backlight or a sufficiently large wind tunnel with ambient temperature control. The test procedure and the minimum performance requirements are based on currently available engineering data.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.
Items per page:
50
1 – 50 of 221558