Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This document establishes the requirements for screw-on type reattachable couplings for use in low temperature hose assemblies.
This SAE Surface Vehicle Technical Information Report, SAE J2836/4, establishes diagnostic use cases between plug-in electric vehicles (PEV) and the electric vehicle supply equipment (EVSE). As PEVs are deployed and include both plug-in hybrid electric (PHEV) and battery electric (BEV) vehicle variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document describes the general information required for diagnostics and SAE J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
This specification covers metric bolts and screws made from a corrosion and heat resistant, nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. The following specification designations and their properties are covered: MA3378 1210 MPa minimum ultimate tensile strength at room temperature 520 MPa stress-rupture strength at 730 °C MA3378-1 1210 MPa minimum ultimate tensile strength at room temperature 726 MPa minimum ultimate shear strength at room temperature
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings machined from AMS3668 material. It shall be used for procurement purposes.
This SAE Aerospace Standard (AS) defines the requirements for a threadless, flexible, high conductive, self-bonding coupling assembly which, when installed on defined ferrules, provides a flexible connection for joining ducting and components in pressurized fluid systems. The assembled coupling is designed to provide interchangeability of parts and components between qualified manufacturers for use from -65 to +265 °F at 130 psi nominal operating pressures and for the service life of the aircraft system. FAR 23.954, FAR 25.603, FAR 25.605, FAR 25.609, FAR 25.613, FAR 25.901, FAR 25.954, and FAR 25.981 certification requirements have identified the need for high-current capable flexible fluid assembled couplings. The coupling assembly does not require inspection or maintenance to remain current capable for the life of the aircraft. This specification provides two test philosophies necessary for low-pressure couplings: 1 Electromagnetic effects/lightning testing of assembled couplings to
This specification covers a magnesium alloy in the form of sand castings.
This specification covers silicone (VMQ) rubber sheet reinforced with glass cloth.
This SAE Recommended Practice describes the test procedure for conducting a rollover test using a dolly fixture designed to laterally trip a vehicle into a roll. Its purpose is to establish a recommended test procedure which will standardize the procedure between different test facilities. A description of the test procedure, test instrumentation, photographic/video coverage, and the rollover fixture is included.
This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.
This specification covers the specific requirements for aluminum alloy 5454 bar, rod, shapes, tube, and wire produced by extrusion.
This document covers metric studs made from a corrosion and heat resistant, age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286. The following specification designations and their properties are covered:
This specification covers the requirements for electrodeposited gold plate.
SCOPE IS UNAVAILABLE
This SAE Recommended Practice provides laboratory test procedures for testing headlamp aim test machines to verify their ability to aim or to inspect the aim of headlamps, fog lamps, and auxiliary high beam lamps. This specification does not apply to aiming devices of the kind covered by SAE J602. This specification does not apply to motorcycle headlamps.
The primary purpose of vehicle forward lighting is not to see the world but to see the road! In their simplest form, headlights help drivers negotiate a safe path on the road. They do this by lighting the roadway according to (a multitude of) specific standards. For decades, discussions concerning the niceties of illuminating potential obstacles in the roadway were little more than an academic pursuit as there simply were not sufficient lumens available from filament light sources to achieve all of the desired tasks no matter how worthy they might be. Not unexpectedly, the technology has evolved with the introduction of high output metal-halide sources, multi-task standards combined with multilevel lighting devices and discrete LED sources offering high luminous efficiencies and the means to deliver the light where it can be most useful. The question now becomes one of determining where the available light should be directed. Every standard advisory group, industry, manufacturer and
This SAE Standard measures the percent thermal efficiency of materials in sleeve form used to contain heat or insulate around a hot component. The percent thermal efficiency (%TE) is determined by measuring the power difference expended by the heat source (cartridge heater) with and without the test sleeve at the specified temperature. See SAE J2302 to measure radiant heat flow of sleeves.
The Mounting Height Task Force was tasked to determine the extent of the problem(s) associated with vehicle headlamps mounted at or above the level of the mirror(s) in passenger vehicles; the level of glare exposure caused by high-mounted headlamps; the appropriate height differential needed to maintain a glare level consistent with past and/or current passenger vehicle headlamp mounting; and the necessary headlamp mounting height necessary to control mirror glare at an accepted/acceptable level. The report herein addresses these passenger vehicle mounting height issues.
This specification covers an aluminum alloy in the form of foil.
This specification covers an ethylene propylene (EPDM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes other than O-rings.
The requirements established in this document are applicable to the IAQG and associated sectors for managing oversight to established requirements contained in 9104-series standards (i.e., 9104/1, 9104/2, 9104/3). The requirements are applicable to IAQG working groups for oversight. NOTE: All required forms are depicted in Appendix A. These form exhibits are provided for reference only; the current versions of these forms are available on the IAQG website.
This document applies to laser proponents involved with the use of laser systems outdoors. It may be used in conjunction with AS4970, ARP5535, ARP5572, and the ANSI Z136 series of laser safety standards.
This SAE Recommended Practice identifies and defines the specifications most commonly used to describe high-speed steel track and articulated rubber-tired clam bunk skidders. The illustrations used are not intended to be descriptive of any existing machine or dictate a combination needed for a particular logging situation. The dimensions indicated are basic and may be supplemented by the individual machine manufacturer.
This SAE Aerospace Recommended Practice (ARP) is intended to be used for laser systems mounted on aircraft and propagated into navigable airspace. This does not include lasers onboard aircraft where the beam is contained within an enclosure so that the beam cannot enter into airspace, nor does it include lasers from satellites and spacecraft in outer space. It may be used in conjunction with AS4970, ARP5535, ARP5572, ARP5293, and the ANSI Z136 laser safety standards.
This SAE Aerospace Standard covers high strength commercial sockets and universal sockets which possess the strength, clearances, and internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the outer 5% of the fastener’s wrenching points. This document provides additional requirements beyond ANSI B107.5 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
This standard covers the requirements for nonseparable antifriction roller bearings.
Items per page:
50
1 – 50 of 219833