Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This SAE Aerospace Recommended Practice (ARP) provides the qualification test procedure requirements for low wattage halogen lamps (less than 35 watts) intended for use primarily in aircraft applications. The purpose of these tests is to provide a laboratory means of determining the performance characteristics of lamps under airplane power and other environmental conditions and to verify the integrity of the lamp design and production processes.
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, and seal. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.
This SAE Aerospace Standard (AS) contains landing gear strength and rigidity requirements which, in combination with other applicable specifications, define the structural design, analysis, test, and data requirements for fixed wing piloted airplanes. These requirements include, but are not limited to, the following: a General specifications: 1 The shock-absorption characteristics and strength of landing-gear units and the strength and rigidity of their control systems and of their carry-through structures. Requirements for wheels, tires, and brakes as they affect air vehicle ground loads are also included. 2 The strength of structures integral with the airplane provided for transmitting catapulting forces to the airplanes, and for engaging shipboard and shore-based arresting gear, and barricades. 3 The strength of anchor-line clamps, and the airplane strength for hoisting, jacking, towing, tie-down, and other ground- or deck-handling conditions. 4 Structural design, analysis, and test
This SAE Aerospace Standard (AS) establishes a Generic Open Architecture (GOA) Framework for application independent hardware/software systems. This document defines the interface classes for the GOA Framework. Supplemental documents define the guidelines for applying the GOA Framework to specific applications.
This document covers flexible and semiflexible, reinforced and unreinforced air hoses fabricated from laminated and impregnated fabric, intended for use in aircraft heating, air conditioning, ventilating, defrosting, and/or deicing systems.
This aerospace specification defines the requirements for a threadless, flexible, conductive, self-bonding coupling assembly which, when installed on fixed cavity ferrules, provides a flexible, current carrying connection for joining tubing and components in aircraft fuel, vent and other systems. The assembled coupling is designed to provide interchangeability of parts and components between qualified manufacturers for the service life of the aircraft system. The assembled coupling is for use from -65 to +200 °F at nominal operating pressures (125 psig for -08 through -64 and 30 psig for -72 through -88). This aerospace specification is a departure from prior qualification practices for assembled couplings. Prior practice sought to validate this type of assembled coupling design by conducting a sequence of tests on sets of coupling assemblies. There were multiple test sequences and each was conducted on a different set of coupling assemblies. Each of these test sequences challenged a
This document provides nomenclature and references to related documents for heavy vehicle event data recorders (HVEDR) for heavy-duty (HD) ground wheeled vehicles. The SAE J2728 series of documents consists of the following:
Electric and alternative fueled vehicles present different hazards for first and second responders than conventional gasoline internal combustion engines. Hydrogen vehicles (H2V) including Fuel Cell Vehicles (FCVs) involved in incidents may present unique hazards associated with the fuel storage and high voltage systems. The electrical hazards associated with the high voltage systems of hybrid-electric vehicles and FCVs are already addressed in the parent document, SAE J2990. This Recommended Practice therefore addresses electric issues by reference to SAE J2990 and supplements SAE J2990 to address the potential consequences associated with hydrogen vehicle incidents and suggest common procedures to help protect emergency responders, tow and/or recovery, storage, repair, and salvage personnel after an incident has occurred. Industry design standards and tools were studied and where appropriate, suggested for responsible organizations to implement.
This SAE Recommended Practice establishes uniform engineering nomenclature for the most common wheel constructions, and their components used on passenger cars, light trucks, and multipurpose vehicles. These wheel constructions are welded disc wheels, cast wheels, forged wheels, composite wheels and hybrid wheels. This nomenclature and the accompanying drawings are intended to define fundamental wheel terms rather than to provide a comprehensive tabulation of all wheel design types.
This SAE Recommended Practice is aimed at ensuring high-quality products of anodized aluminum automotive components in terms of durability and appearance. Decorative sulfuric acid anodizing has been well developed over the last several decades in the aluminum industry. Exterior and interior performance demonstrated that parts processed to this document meet long-term durability requirements. Since the treatment of processing variables is outside the scope of this document, it is important for applicators of this coating to develop an intimate knowledge of their process, and control all parameters that affect the quality of the end product. The use of techniques such as statistical process control (SPC), capability studies, design of experiments, process optimization, etc., are critical to produce material of consistently high quality.
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal directional drilling (HDD) machines as defined by ISO 21467:2023.
This SAE Information Report applies to structural integrity, performance, drivability, and serviceability of personally licensed vehicles not exceeding 10000 pounds GVWR such as sedans, crossovers, SUVs, MPVs, light trucks, and van-type vehicles that are powered by gas and alternative fuel such as electric, plug-in hybrid, or hybrid technologies. It provides engineering direction to vehicle modifiers in a manner that does not limit innovation, and it specifies procedures for preparing vehicles to enhance safety during vehicle modifications. It further provides guidance and recommendations for the minimum acceptable design requirements and performance criteria on general and specific structural modifications, thereby allowing consumers and third-party payers the ability to obtain and purchase equipment that meets or exceeds the performance and safety of the OEM production vehicle.
This document is limited to the aerospace industry, where an approved manufacturer requests a supplier to ship an article against the approved manufacturer’s quality system directly to a customer. The direct ship process is not required or applicable to standard parts or military parts. In this process, the approved manufacturer is responsible for assurance that the article conforms to type design information.
This specification covers a low-alloy steel in the form of bare welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This SAE Aerospace Standard (AS) aims at identifying the design criteria and testing methods adequate to guarantee the ultimate load and operational dependability of cargo restraint strap assemblies with a typical 22250 N (5000 lbf) rated ultimate tension load capability, as used by the airline industry in order to restrain cargo on board civil transport aircraft during flight: a cargo loaded and tied down onto airworthiness certified air cargo pallets, themselves restrained into aircraft lower deck or main/upper deck cargo systems and meeting the requirements of NAS 3610 or AS36100, or b non-unitized individual pieces of cargo, or pieces of, cargo placed onto an unrestrained (“floating”) pallet into either lower deck or main deck containerized cargo compartments of an aircraft.
This SAE Standard covers complete general and dimensional specifications for refrigeration tube fittings of the flare type specified in Figures 1 to 42 and Tables 1 to 15. These fittings are intended for general use with flared annealed copper tubing in refrigeration applications. Dimensions of single and double 45 degree flares on tubing to be used in conjunction with these fittings are given in Figure 2 and Table 1 of SAE J533. The following general specifications supplement the dimensional data contained in Tables 1 to 15 with respect to all unspecified details.
This document describes a fuel-consumption test procedure that utilizes industry accepted data collection and statistical analysis methods to determine the difference in fuel consumption between vehicles with a gross vehicle weight of more than 10000 pounds. This test procedure can be used for an evaluation of two or more different vehicles but is not to be used to evaluate a component change. Although on-road testing is allowed, track testing is the preferred method because it has the greatest opportunity to minimize weather and traffic influences on the variability of the results. All tests shall be conducted in accordance with the weather constraints described within this procedure and shall be supported by collected data and analysis. This document provides information that may be used in concert with SAE Recommended Practices SAE J1264, SAE J1252, SAE J1321, and SAE J2966, as well as additional current and future aerodynamic and vehicle performance SAE standards.
This document provides an overview on how and why EGR coolers are utilized, defines commonly used nomenclature, discusses design issues and trade-offs, and identifies common failure modes. The reintroduction of selectively cooled exhaust gas into the combustion chamber is just one component of the emission control strategy for internal combustion (IC) engines, both diesel and gasoline, and is useful in reducing exhaust port emission of nitrogen oxides (NOx). Other means of reducing NOx exhaust port emissions are briefly mentioned, but beyond the scope of this document.
This SAE Information Report establishes a minimum level of uniform recipes for contaminants which may be used when durability testing pneumatic components to obtain additional information on how a device may perform under more true-to-life operating conditions. This type of contamination testing, however, is not meant to replace the type of performance testing described in SAE J1409 and SAE J1410. Durability testing in the presence of contamination will yield results more reflective of actual in-service field conditions and provide an additional evaluation of pneumatic devices. While the contaminant supply rate and other test criteria of the device being tested must be set by the device manufacturer or user, the items covered in this document will be:
This SAE Standard includes names of major components and parts peculiar to this type of equipment. The illustrations are not intended to show all existing commercial machines or to be exactly descriptive of any particular machine. They have been selected to depict principles used in identifying specific mechanisms and to identify useful dimensional relationships.
This SAE Recommended Practice identifies and defines terms specifically related to brake systems.
Items per page:
50
1 – 50 of 221567