Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. In all cases where provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. This classification is based on SI units.
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for automotive units with the primary drive hypoid gears, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. The information contained within is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI). A complete listing of qualification submission requirements and
The pressurization system design considerations presented in this AIR deal with human physiological requirements, characteristics of pressurization air sources, methods of controlling cabin pressure, cabin leakage control, leakage calculation methods, and methods of emergency cabin pressure release.
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
This SAE Standard provides safety requirements for vacuum excavation and sewer cleaning equipment. This document is not intended to cover equipment addressed by other on-road federal, state, and local regulations. Truck-mounted or trailer-mounted vehicles are required to meet local or regional on-road requirements, as applicable.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement CAN with flexible data rate (CAN FD) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/11_0500 interface shall be compliant to the CAN with flexible data rate (CAN FD) feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement the internet protocol version 6 (IPv6) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/15_0500 interface shall be compliant to the internet protocol version 6 (IPv6) feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/13_0500 (ethernet), SAE J2534-2/BA_0500, and SAE J2534-2/RE_0500 documents.
This report lists documents that aid and govern the design, development, certification, and utilization of aerospace electronic engine control systems. The report lists the military and industry specifications and standards that are commonly used in electronic engine control system design. Also included are Airworthiness Authority documents and requirements associated with certification. However, these lists are not necessarily complete. The specifications and standards section has been divided into two parts: a master list, and a categorized list that provides a functional breakdown and cross-reference of these documents. For specifications and standards, the issue available during the latest revision to this document is listed. Details of current revisions for many documents are available in the Department of Defense Index of Specifications and Standards (DODISS). It should be noted that not all of these documents are referenced or even recognized by all certification authorities. In
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the exhaust sound pressure levels of motorcycles under stationary conditions. Since initial publication, it has been successfully applied to regulation and monitoring of sound pressure levels of off-highway vehicles, and that remains its recommended application. Users of SAE J1287 for the purpose of roadside enforcement of sound pressure levels for on-highway motorcycles have reported difficulties with its implementation in that application. In response, SAE J2825 was developed, and is recommended for measurement of exhaust sound pressure levels of stationary on-highway motorcycles. Care must be taken not to confuse stationary sound pressure levels with total motorcycle sound pressure levels. This test does not evaluate total motorcycle sound during operation. For this purpose, SAE J331 or SAE J47 is recommended. Any allowable sound limits (dBA) set in relation to SAE J1287 for exhaust
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers a polytetrafluoroethylene (PTFE) modified fluorosilicone (FVMQ) rubber in the form of molded shapes, molded rings (ASTM D 1414), and compression seals.
This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall tubing.
This specification covers an aluminum alloy in the form of permanent mold castings.
This specification covers continuous, multiple-strand, roving of Type "S-2" glass impregnated with a heat-curable epoxy resin matrix and processed to a "B" stage condition.
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
This Aerospace Recommended Practice (ARP) provides recommendations for the design and test requirements for a hydraulic thermal relief valve. The thermal relief valve is intended for use in a civil or military aircraft hydraulic system with a rated system pressure up to 5000 psi (34500 kPa).
This specification covers a compressed non-asbestos fiber and acrylonitrile butadiene (NBR) rubber in the form of sheet.
This specification covers a two-component silicone rubber sealant and compatible primers.
This specification covers an aluminum bronze alloy in the form of centrifugal and chill castings.
This specification covers the requirements for electrodeposed lead on metal parts.
This specification establishes the minimum requirements for fused filament fabrication (FFF) feedstock.
This SAE Aerospace Standard (AS) defines a series of standardized tube walls to be used for high pressure hydraulic tubing. These tube walls are applicable to all homogenous tube materials (i.e., aluminum, steel, titanium) throughout a rated pressure range of 1000 to 8000 psi and a maximum rated operating temperature range of 160 to 450 °F. All future aerospace applications for which a required tube outside diameter/tube wall combination is not presently available shall be selected from the table contained herein (see Figure 1).
This specification covers an ethylene propylene elastomer in the form of molded sheet and shapes, color coded purple per ARP1527.
This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6498 cover UNS K23280 with other quality levels.
This User Guide describes the content of the Enterprise Architect (EA) version of the UCS Architectural Model and how to use this model within the EA modeling tool environment. The purpose of the EA version of the UCS Architectural Interface Control Document (ICD) model is to provide a working model for Enterprise Architect tool users and to serve as the source model for the Rational Software Architect (RSA) and Rhapsody models (AIR6516 and AIR6517). The AIR6515 EA Model has been validated to contain the same content as the AS6518 model for: all UCS ICD interfaces all UCS ICD messages all UCS ICD data directly or indirectly referenced by ICD messages and interfaces the Domain Participant, Information, Service, and Non-Functional Properties Models
Items per page:
50
1 – 50 of 219833