Results
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
This specification covers the installation of aircraft interior lighting for military aircraft.
This specification establishes the procedures used to produce a hard anodic coating on magnesium alloys and the properties of the coating.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This document provides recommendations to identify battery group sizes and dimensions for 6 V, 8 V, 12 V, and 24 V lead acid batteries.
This specification covers a manganese alloy in the form of powder, preforms, and a viscous mixture (paste) of the powder in a suitable binder.
This SAE Recommended Practice defines the set-up and procedure for conducting the SAE Single Tooth Bending Fatigue Test. The details of the test fixture to be used (referred henceforth as “the test fixture” in this document) and gear test sample and the procedures for testing and analyzing the data are presented in this document.
The scope of this document is to: 1 Specify techniques to detect SC parts using electrical testing. 2 Provide various levels of electrical testing that can be used by the User to define test plans for detecting SC parts. 3 Provide minimum requirements for testing laboratories so that User/Requester can determine which test houses have the necessary capabilities. (For example: technical knowledge, equipment, procedures and protocols for performing electrical testing for verification analysis.) Note: User/Requester is defined in AS6171 General Requirements 4 Specify Burn-In and environmental tests. The environmental tests include Temperature Cycling for Active Devices and Thermal Shock for Passive Devices. Seal Tests are described and recommended for hermetic devices. The following terminology is used throughout this document: a Shall = is mandatory; b Should = is recommended; and c Will = is planned (is considered to be part of a standard process). If AS6171/7 is invoked in the contract
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7273 rubber. It shall be used for procurement purposes.
An attempt has been made to consider all features of seal ring design including configuration, materials, hardness, dimensions, surface finishes, surface treatment, leak testing, and general quality. In addition to this, allowable cylinder breathing and general quality requirements of mating hardware are discussed. Also, at the end of this report, there is a brief paragraph on other types of seal rings.
This specification covers a low-alloy steel in the form of welding wire.
This SAE Recommended Practice establishes the antilock brake system (ABS) sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on or integral to the inboard end of spoke wheels, hubs, rotors, and hub-rotor assemblies on the following axle designations as defined in SAE J1842. a FF b FL c FC d FH e L f R g U h W j N k P
This specification covers a magnesium alloy in the form of sand castings.
This procedure applies to directional control valves or other valves which in various positions direct or block fluid flow as applied to Off-Road Self-Propelled Work Machines as referenced in SAE J1116.
Over the past two and one-half decades several metal clad fibers and fabrics have been developed to provide aerospace vehicle designers with a conductive, lighter weight alternative to coated copper, coated stainless steel and steel wire used for cable and wire shielding and harness overbraids on electrical cables. Several of these candidates have been unable to provide the strength or thermal stability necessary for the aerospace environment. However, several polymer-based products have shown remarkable resistance to the rigorous environment of aerospace vehicles. Concurrent with these fiber developments, there have been changes in the structures of aerospace vehicles involving greater use of nonmetallic outer surfaces. This has resulted in a need for increased shielding of electrical cables which adds substantial weight to the vehicle. Thus, a lighter weight shielding material has become more critical to meet the performance requirements of the vehicle. This report covers the
This specification covers a one-part fluorosilicone (FVMQ) adhesive/sealant, supplied in cartridges, suitable for extrusion and curing to an elastomeric material upon exposure to air. It also covers a compatible primer.
This specification covers design and performance requirements of fiber optic splices for optical distribution systems in aerospace vehicles and provides a means of procurement of such devices.
This SAE Aerospace Recommended Practice (ARP) specifies for quality requirements that are additive to a procurement document or contract, where an organization: a needs to provide additional guidance for suppliers and other organizations in the delivery of products, goods and services in accordance with stated quality demands, and b needs to provide information in addition or in absence of existing quality system requirements to provide the assurance of conformity to customer and applicable regulatory requirements. NOTE: In this ARP, the term ‘product’ applies only to the product intended for, or required by, a customer.
This specification covers a low-carbon steel in the form of round wire clad with electrolytic copper.
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, and components. Said actuators are used for applying cam type foundation brakes by slack adjuster means.
This SAE Aerospace Information Report (AIR) provides a description of a screening method for use in the field for verifying an AMS 1428 anti-icing fluid is above its minimum low shear viscosity as published with holdover time guidelines. The test will determine if the fluid is (a) satisfactory, (b) unsatisfactory, or (c) borderline needing more advanced viscometry testing. Other field tests may be required to determine if an anti-icing fluid is useable, such as refractive index, appearance or other tests as may be recommended by the fluid manufacturer.
This recommended practice provides the design criteria for static elastomeric O-ring seals used specifically in engine and engine control systems. It provides axial compression (face type) groove dimensions for aerospace metric O-ring sizes specified in MA2010. The conditions considered to formulate the design criteria are also described, e.g., seal squeeze and groove volume to accommodate O-ring swell. NOTE: Tables of O-ring groove dimensions are included based on the design criteria specified herein. Dimensions in this document are in millimeters unless otherwise specified.
This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.
This SAE Aerospace Recommended Practice (ARP) contains guidelines and recommendations for subsonic airplane air conditioning systems and components, including requirements, design philosophy, testing, and ambient conditions. The airplane air conditioning system comprises that arrangement of equipment, controls, and indicators that supply and distribute air to the occupied compartments for ventilation, pressurization, and temperature and moisture control. The principal features of the system are: a A supply of outside air with independent control valve(s). b A means for heating. c A means for cooling (air or vapor cycle units and heat exchangers). d A means for removing excess moisture from the air supply. e A ventilation subsystem. f A temperature control subsystem. g A pressure control subsystem. Other system components for treating cabin air, such as filtration and humidification, are included, as are the ancillary functions of equipment cooling and cargo compartment conditioning
This specification covers polyurethane systems consisting of an isocyanate component and other components containing a polyol and other ingredients which, when mixed and cured, produce thermosetting, rigid, cellular products.
Items per page:
50
1 – 50 of 222094