Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This SAE Standard describes standardized medium-independent messages needed by information service providers for Advanced Traveler Information Systems (ATIS). The messages contained herein address all stages of travel (informational, pre-trip and en route), all types of travelers (drivers, passengers, personal devices, computers, other servers), all categories of information, and all platforms for delivery of information (in-vehicle, portable devices, kiosks, etc.).
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of any USB cable assemblies and associated connections that constitute the electrical connection systems between the consumer peripheral interface and the USB computer source in road vehicle applications. These procedures are only applicable to the USB connector and the cable. Unless otherwise specified, all of the tests listed in this specification are for both consumer and nonconsumer interface connectors.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Aerospace Standard (AS) establishes a Generic Open Architecture (GOA) Framework for application independent hardware/software systems. This document defines the interface classes for the GOA Framework. Supplemental documents define the guidelines for applying the GOA Framework to specific applications.
Various gas systems are classified in a broad sense, component operation is described in moderate detail, pertinent design parameters are discussed, and possible modes for system operation are listed.
This specification covers a tin-lead alloy in the form of bars, ingots, pellets, ribbon, and round wire.
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self-propelled work machines as defined by SAE J1116 (limited to categories of (1) construction, and (2) general purpose industrial).
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
This document establishes general design criteria, tolerances, and limits of application for tooling, fixtures, and accessories for mounting and driving gas turbine engine rotors on horizontal and vertical balancing machines.
This specification covers silicone (VMQ) rubber sheet reinforced with glass cloth.
This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings.
This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall tubing.
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This specification covers the requirements for three types and three classes of mechanically deposited cadmium, tin-cadmium or zinc coatings on metallic surfaces by impacting (peen plating).
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers an aluminum alloy in the form of pre-alloyed powder.
This specification covers coated round rods manufactured by the pultrusion process from glass fiber roving and a weather-resistant polyester resin binder in the form of straight lengths or in coils.
All safety glazing materials used in motor vehicles and motor vehicle equipment operating on land highways should comply with the requirements of the American National Standard, ANSI/SAE Z-26.1. The American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways—Safety Standard, ANSI/SAE Z-26.1-1996 is the latest complete updated version and is referred to hereafter as “the safety standard.” This SAE Recommended Practice is not intended to preclude references to any governmental law, ordinance, or regulation which might apply to the glazing of motor vehicles and motor vehicle equipment operating on land highways.
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Items per page:
50
1 – 50 of 222741