Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The intent of this standard is to establish a framework to assure that all evaporators conforming to its requirements demonstrate an acceptable health and safety environment for vehicle occupants as determined from the completed risk assessment. R-744 and low pressure (i.e., non-transcritical refrigerants with a critical temperature between 85 and 120 °C) mobile air conditioning (MAC) refrigerant evaporators shall meet the testing and labeling requirements of this standard. SAE J639 contains a list of all refrigerants considered acceptable for use in mobile thermal systems for which this standard applies when the refrigerant is used in a direct expansion architecture. SAE J639 also requires an assessment to be performed to minimize reasonable risks in MAC systems. The evaporator (as designed and manufactured) shall be part of that risk assessment, and it is the responsibility of the vehicle manufacturer to ensure all relevant aspects of the evaporator are included. It is the
This specification covers an aluminum alloy in the form of rolled or cold-finished bars, rods, wire, and flash-welded rings and of stock for flash-welded rings.
This specification covers a cobalt alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.
This specification covers a titanium alloy in the form of wire for welding filler metal (see 8.5).
This specification covers an aluminum alloy in the form of honeycomb core in a non-hexagonal, flexible cell configuration with the core being treated for increased corrosion resistance and furnished only in the expanded form (see 8.5).
This specification covers a titanium alloy in the form of welding wire (see 8.5).
This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inches (6.35 to 102.0 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a palladium-silver alloy in the form of round wire 0.004 to 0.080 inch (0.10 to 2.03 mm), inclusive, in nominal diameter (see 8.5).
This specification covers a titanium alloy in the form of pre-alloyed powder.
This specification covers a titanium alloy in the form of sheet, strip, and plate on product 0.008 to 3.000 inches (0.20 to 76.20 mm), inclusive, in thickness (see 8.6).
The specification covers a titanium alloy in the form of wire (see 8.5).
The verification matrix (VM) in this slash sheet is intended for use to establish compliance to AS6174A. This slash sheet is applicable to AS6174A. Nothing in this slash sheet, however, supersedes applicable laws and regulations, unless a specific exemption has been obtained through judicial/legal channels.
This specification covers one grade of commercially pure titanium in the form of wire for welding filler metal (see 8.5).
This specification covers a titanium alloy in the form of bars, wire, forgings, and flash-welded rings up through 3.999 inches (101.57 mm), inclusive, and stock for forging, flash-welded rings, or heading (see 8.6).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches (127.00 mm), inclusive, in nominal diameter or least thickness between parallel sides (bars, rods, wire, profiles) or nominal wall thickness (tubing) (see 8.5).
This practice provides a method for evaluating microhardness and microstructure very close (0.002 inch (0.051 mm) or less) to the surface of a disk specimen. Specific accept/reject criteria for partial decarburization (3.7.1), inadvertent carburization/nitriding (3.7.3), total decarburization/intergranular oxidation (3.8), and other characteristics evaluated are to be found in the applicable specification where this ARP is referenced.
This SAE Standard applies to lead-acid 12 V heavy-duty storage batteries as described in SAE J537 and SAE J930 for uses in starting, lighting, and ignition (SLI) applications on motor vehicles and/or off-road machines. These applications have some of the following characteristics: High levels of power are required to start the vehicle’s internal combustion engine. The need to supply this power limits the maximum depth of discharge to a fraction of the total capacity of the battery. The battery must be maintained at a charge level sufficient to perform this primary function by the vehicle’s voltage-regulated charging system. The vehicle’s engine powers a voltage-regulated charging system that limits the charging voltage when spinning at sufficient speed and when total loads do not exceed its output limits. The battery is subject to deeper discharging than a typical automotive application as a result of the following conditions: High daily hours of use High numbers of starts per day
This SAE Recommended Practice describes the recommended methods for testing flexible harness coverings for use on ground vehicle electrical distribution systems. It shall apply to all tapes, extruded tube, and textile tube.
This SAE Aerospace Standard (AS) covers any protective system that serves the stated purpose.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Aerospace Recommended Practice (ARP) describes a method for evaluating the performance of filter elements designed for aerospace hydraulic systems. The performance is measured and reported in terms of filtration ratios and stabilized contamination levels while testing with cyclic flow.
This document applies to regulatory/approving authorities involved with decisions regarding the use of high-intensity light (HIL) directed into the navigable airspace. For the purpose of this document, lights greater than 0.25 million candlepower meet the minimum threshold of an HIL. Lights not directed or reflected into the navigable airspace are not usually considered to interfere with aircraft operations. HILs include laser-derived light sources; other laser systems are beyond the scope of this document. This document addresses adverse effects of HILs on humans, such as visual interference. HIL effects on Unmanned Aircraft Systems (UASs) are beyond the scope of this document.
This specification covers an aluminum alloy in the form of castings (see 8.10).
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling, and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling oxygen cylinders while installed on aircraft, directly or through an intermediate charging port.
Items per page:
50
1 – 50 of 219667