Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inches (6.35 to 102.0 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches (127.00 mm), inclusive, in nominal diameter or least thickness between parallel sides (bars, rods, wire, profiles) or nominal wall thickness (tubing) (see 8.5).
This specification covers a titanium alloy in the form of bars, wire, forgings, and flash-welded rings up through 3.999 inches (101.57 mm), inclusive, and stock for forging, flash-welded rings, or heading (see 8.6).
This specification covers a titanium alloy in the form of welding wire (see 8.5).
This specification covers one grade of commercially pure titanium in the form of wire for welding filler metal (see 8.5).
This specification covers a palladium-silver alloy in the form of round wire 0.004 to 0.080 inch (0.10 to 2.03 mm), inclusive, in nominal diameter (see 8.5).
The verification matrix (VM) in this slash sheet is intended for use to establish compliance to AS6174A. This slash sheet is applicable to AS6174A. Nothing in this slash sheet, however, supersedes applicable laws and regulations, unless a specific exemption has been obtained through judicial/legal channels.
The specification covers a titanium alloy in the form of wire (see 8.5).
This specification covers a titanium alloy in the form of sheet, strip, and plate on product 0.008 to 3.000 inches (0.20 to 76.20 mm), inclusive, in thickness (see 8.6).
This specification covers an aluminum alloy in the form of rolled or cold-finished bars, rods, wire, and flash-welded rings and of stock for flash-welded rings.
This specification covers a cobalt alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.
The intent of this standard is to establish a framework to assure that all evaporators conforming to its requirements demonstrate an acceptable health and safety environment for vehicle occupants as determined from the completed risk assessment. R-744 and low pressure (i.e., non-transcritical refrigerants with a critical temperature between 85 and 120 °C) mobile air conditioning (MAC) refrigerant evaporators shall meet the testing and labeling requirements of this standard. SAE J639 contains a list of all refrigerants considered acceptable for use in mobile thermal systems for which this standard applies when the refrigerant is used in a direct expansion architecture. SAE J639 also requires an assessment to be performed to minimize reasonable risks in MAC systems. The evaporator (as designed and manufactured) shall be part of that risk assessment, and it is the responsibility of the vehicle manufacturer to ensure all relevant aspects of the evaporator are included. It is the
This SAE Standard applies to lead-acid 12 V heavy-duty storage batteries as described in SAE J537 and SAE J930 for uses in starting, lighting, and ignition (SLI) applications on motor vehicles and/or off-road machines. These applications have some of the following characteristics: High levels of power are required to start the vehicle’s internal combustion engine. The need to supply this power limits the maximum depth of discharge to a fraction of the total capacity of the battery. The battery must be maintained at a charge level sufficient to perform this primary function by the vehicle’s voltage-regulated charging system. The vehicle’s engine powers a voltage-regulated charging system that limits the charging voltage when spinning at sufficient speed and when total loads do not exceed its output limits. The battery is subject to deeper discharging than a typical automotive application as a result of the following conditions: High daily hours of use High numbers of starts per day
This SAE Recommended Practice describes the recommended methods for testing flexible harness coverings for use on ground vehicle electrical distribution systems. It shall apply to all tapes, extruded tube, and textile tube.
This SAE Aerospace Standard (AS) covers any protective system that serves the stated purpose.
This practice provides a method for evaluating microhardness and microstructure very close (0.002 inch (0.051 mm) or less) to the surface of a disk specimen. Specific accept/reject criteria for partial decarburization (3.7.1), inadvertent carburization/nitriding (3.7.3), total decarburization/intergranular oxidation (3.8), and other characteristics evaluated are to be found in the applicable specification where this ARP is referenced.
This SAE Aerospace Standard establishes the requirements for a V-retainer coupling, flanges, and seal suitable for joining high-pressure and high-temperature ducting in aircraft bleed air systems. The rigid coupling joint assembly, hereafter referred to as “the joint,” shall operate within the temperature range of -65 to +1200 °F.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements and procedures for three classes of gas, vacuum, liquid, and low-pressure carburizing (LPC) and related heat treatment of parts fabricated from carburizing-grade steels. Parts made from steels other than those specified in the detail specifications may be heat treated in accordance with the applicable requirements using processing temperatures, times, and other parameters recommended by the material producer. This specification does not cover pack carburizing.
This SAE Aerospace Recommended Practice (ARP) provides information and guidance for the control of hazardous laser exposure in the navigable airspace. This ARP does not address techniques that pilots can apply to mitigate laser illuminations during a critical phase of flight. Such mitigation strategies are described in ARP6378.
This document applies to laser proponents involved with the use of laser systems outdoors. It may be used in conjunction with AS4970, ARP5535, ARP5572, and the ANSI Z136 series of laser safety standards.
This specification covers a corrosion-resistant nickel-copper alloy in the form of seamless tubing.
SCOPE IS UNAVAILABLE
SCOPE IS UNAVAILABLE.
This document applies to regulatory/approving authorities involved with decisions regarding the use of high-intensity light (HIL) directed into the navigable airspace. For the purpose of this document, lights greater than 0.25 million candlepower meet the minimum threshold of an HIL. Lights not directed or reflected into the navigable airspace are not usually considered to interfere with aircraft operations. HILs include laser-derived light sources; other laser systems are beyond the scope of this document. This document addresses adverse effects of HILs on humans, such as visual interference. HIL effects on Unmanned Aircraft Systems (UASs) are beyond the scope of this document.
SCOPE IS UNAVAILABLE.
This specification defines limits of variation for determining acceptability of composition of cast and wrought corrosion and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy parts and materials acquired from a producer.
This specification covers a copper alloy (phosphor bronze) in the form of sheet, strip, and plate (see 8.6).
This specification covers an aluminum alloy in the form of plate 0.500 to 4.500 inches (12.7 to 114.3 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy in the form of castings (see 8.10).
Items per page:
50
1 – 50 of 219663