Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This document presents criteria for flight deck controls and displays for Airborne Collision Avoidance Systems.
This document establishes the minimum training and qualification requirements for ground-based aircraft deicing methods and procedures. All guidelines referred to herein are applicable only in conjunction with the applicable documents. Due to aerodynamic and other concerns, the application of deicing fluids shall be carried out in compliance with engine and aircraft manufacturers’ recommendations. The scope of training should be adjusted according to local demands. There are a wide variety of winter seasons and differences of the involvement between deicing operators, and therefore, the level and length of training should be adjusted accordingly. However, the minimum level of training shall be covered in all cases. As a rule of thumb, the amount of time spent in practical training should equal or exceed the amount of time spent in classroom training.
This SAE Standard provides test procedures, requirements, and guidelines for reflex reflectors used on vehicles 2032 mm or more in overall width. Reflex reflectors conforming to these requirements may also be used on vehicles less than 2032 mm in overall width.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for the system of optical warning devices used on emergency vehicles.
This SAE Standard provides test procedures, requirements, and guidelines for clearance, side marker, and identification lamps.
This SAE Recommended Practice describes requirements for lamps, reflective devices, and associated equipment for signaling to enable safe operation in darkness and other conditions of reduced visibility.
This SAE Standard references the performance and functional requirements of the International Electrotechnical Commission (IEC) and its U.S. member, the American National Standards Institute (ANSI). By referring to IEC/ANSI and its standards concerning light source (bulb) sockets, light source (lamp) holders, and gages, this document recognizes the need for harmonized standards world-wide for what are typically commodity items. Additional requirements are noted.
Since it is impossible to be all inclusive and cover every aspect of the design/validation process, this document can be used as a basis for preparation of a more comprehensive and detailed plan that reflects the accumulated “lessons learned” at a particular company. The following areas are addressed in this document: 1 Contemporary perspective including common validation issues and flaws. 2 A Robustness validation (RV) process based on SAE J1211 handbook and SAE J2628. 3 Design checklists to aid in such a RV process.
This SAE Standard provides general design performance requirements and related test procedures for composite lighting unit assemblies, other than signaling and marking devices, used on earthmoving and road building and maintenance off-road work machines as defined in SAE J1116.
This SAE Recommended Practice provides supporting information for the emission and immunity measurement procedures defined in the SAE J1752 series of documents.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This SAE Recommended Practice provides standardized laboratory tests, test methods, and performance requirements applicable to signal and marking devices used on vehicles 2032 mm or more in overall width.
This SAE Recommended Practice provides definitions of common terms used in SAE Documents pertaining to motor vehicle lighting. It covers not only basic lighting terms but also terms which identify major segments of technical reports.
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cleaners intended for use on motor vehicles.
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than, equal to, or greater than 2032 mm in overall width.
This Technical Information Report defines the diagnostic communication protocol Keyword Protocol 1281 (KWP1281). This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECUs, in which a KWP1281 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the KWP1281 protocol in enough detail to support the requirements necessary to implement the communication protocol in an SAE J2534 interface device.
This document establishes performance, material, and design requirements and design guidelines for halogen replaceable light sources used in road illumination devices for forward lighting. Non-halogen filament light sources suitable for forward lighting are specified in SAE J573. The terms “high beam filament” and “low beam filament” used throughout this document refer only to typical use, not to a mandatory, exclusive, or universal function of the filaments. This SAE Recommended Practice is periodically updated to keep pace with experience and technical advances.
This part of SAE J1113 specifies test methods and procedures for testing electromagnetic immunity (of vehicle radiation sources) of electronic components for passenger cars and commercial vehicles. To perform this test method, the electronic module along with the wiring harness (prototype or standard test harness) and peripheral devices will be subjected to the electromagnetic disturbance generated inside an absorber-lined chamber. The electromagnetic disturbances considered in this part of SAE J1113 are limited to continuous narrowband electromagnetic fields. Immunity measurements of complete vehicles are generally only performed at the vehicle manufacturer. The reasons, for example, are high costs of a large absorber-lined chamber, preserving the secrecy of prototypes, or the large number of different vehicle models. Therefore, for research, development and quality control, a laboratory measuring method shall be applied by the manufacturers. Part 1 of SAE J1113 specifies the general
This SAE Recommended Practice provides procedures and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.
This SAE Standard provides the minimum requirements for primary and auxiliary jumper cable plug and receptacle for the truck-trailer and converter dolly jumper cable systems for 12 VDC nominal applications. It includes the test procedures, design, and performance requirements.
Most signal and marking lighting devices have light sources (bulbs), which can be based on either filament or LED technology. To assure field replacement, it is important that light source types employed be readily available in normal service channels. This document defines the physical, electrical, and photometric characteristics necessary to achieve a proper replacement for popular types of signal and marking light sources. Some of the design characteristics in this document are listed solely for the sake of standardization and are not intended to describe the performance of lighting devices (lamp assemblies) on the vehicle. Halogen filament light sources suitable for signal and marking lighting are specified in SAE J2560.
This SAE Standard defines a component-level test procedure to evaluate automotive electrical and electronic components for Conducted Emissions of transients, and for other electromagnetic disturbances, along battery feed (B+) or switched ignition inputs of a Device Under Test (DUT). Test apparatus specifications outlined in this procedure were developed for components installed in the 12-V passenger cars, light trucks, 12 V heavy-duty trucks, and vehicles with 24 V systems.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, material requirements, design requirements, and design guidelines for sealed beam headlamps.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers an aluminum alloy in the form of sheet from 0.020 to 0.249 inch (0.51 to 6.32 mm), inclusive, in thickness (see 8.6).
This SAE Information Report identifies and defines the preferred technical guidelines relating to safety for vehicles that contain High Voltage (HV), such as Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), Plug-In Hybrid Electric Vehicle (PHEV), Fuel Cell Vehicles (FCV) and Plug-In Fuel Cell Vehicles (PFCV) during normal operation and charging, as applicable. Guidelines in this document do not necessarily address maintenance, repair, or assembly safety issues.
This document specifies that black is the only color that can be used for the insulator at the bottom of the base of T-1 and T-1 ¾ Flanged Base lamps.
This specification covers three types of aircraft position lights.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device-specific tests and requirements can be found in applicable SAE Technical Reports.
The process detailed within this document is generic and applies to the entire end-to-end health management capability, covering both on-board and on-ground elements, in both commercial and military applications throughout their lifecycle. This ARP addresses a gap in guidance related to usage of ground-based health management equipment for airworthiness credit, ensuring a level of integrity commensurate with the potential aircraft-level consequences of the relevant failure conditions. The practical application of this standardized process is detailed in the form of a checklist. The on-board elements described here are typically the source of the data acquisition used for off-board analysis. The on-board aspects relating to airworthiness and/or safety of flight, e.g., pilot notification, are addressed by existing guidance and policy documents. If a proposed health management capability for airworthiness credit involves modification of the on-board systems, the substantiation of those
This SAE Standard covers low voltage primary cable intended for use at a nominal system voltage of 60 VDC (25 VAC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
This SAE Aerospace Recommended Practice (ARP) outlines the functional and design requirements for a self-propelled belt conveyor for handling baggage and cargo at aircraft bulk cargo holds. Additional considerations and requirements may legally apply in other countries. As an example, for operation in Europe (EU and EFTA), the applicable EN standards shall be complied with.
This SAE Aerospace Recommended Practice (ARP) outlines a standard method for the checkout and calibration of electromagnetic interference measurement antennas. Its primary application is for use when measuring a source 1 m from the antenna in a shield room versus a source at a greater distance (far field). This is the typical distance used in performing military EMC testing. Thus, this is a method of calibration. Shield room characteristics are not considered. It does not address an unknown distributed source. Yet it is close to reality since it is based on another antenna that represents a distributed source. This document presents a technique to determine antenna factors for antennas used primarily in performing measurements in accordance with 2.1 and 2.2. The purpose of Revision B is to include the calibration of other antennas, such as small loop antennas that are also specified for use in these same references. Revision D includes a specific procedure for loop antennas that are
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU. It further specifies additional
This specification covers a corrosion-resistant steel in the form of investment castings homogenized and solution and precipitation heat treated to 180 ksi (1241 MPa) tensile strength.
This specification covers two types of thickened, water base temporary coating remover in the form of an alkaline liquid.
This specification covers materials in the form of a liquid used to remove smut from aluminum surfaces treated with etch-type oxidation and corrosion removers.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of carbon and low-alloy steel forgings.
This document provides design guidelines, test procedure references, and performance requirements for omnidirectional and selective coverage optical warning devices used on authorized emergency, maintenance, and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
Items per page:
50
1 – 50 of 219501