Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters NC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.
This document defines various vehicular noises and vibrations that are attributed to being created by the foundation brake components of the vehicle, particularly on passenger cars and light trucks. These definitions cover both disc and drum brakes. The frequency ranges from near zero Hz (tactile sensations) all the way up to 17 kHz, or the upper limit of normal hearing. These noises and vibrations may either directly radiate off the brake system or provide the excitation energy that causes other vehicle components to react.
This document provides an overview on how and why EGR coolers are utilized, defines commonly used nomenclature, discusses design issues and trade-offs, and identifies common failure modes. The reintroduction of selectively cooled exhaust gas into the combustion chamber is just one component of the emission control strategy for internal combustion (IC) engines, both diesel and gasoline, and is useful in reducing exhaust port emission of nitrogen oxides (NOx). Other means of reducing NOx exhaust port emissions are briefly mentioned, but beyond the scope of this document.
This SAE Information Report establishes a minimum level of uniform recipes for contaminants which may be used when durability testing pneumatic components to obtain additional information on how a device may perform under more true-to-life operating conditions. This type of contamination testing, however, is not meant to replace the type of performance testing described in SAE J1409 and SAE J1410. Durability testing in the presence of contamination will yield results more reflective of actual in-service field conditions and provide an additional evaluation of pneumatic devices. While the contaminant supply rate and other test criteria of the device being tested must be set by the device manufacturer or user, the items covered in this document will be:
This glossary of tire military/industry represents the latest state-of-the-art terms and definitions for military use. This SAE Recommended Practice shall remain open for comments from the reader and shall also be reviewed and updated periodically. Many similar terms and definitions were reviewed from which the ones best applied to military use were selected. It is the purpose of this task force to provide technical definitions in present day use.
The terms included in the Glossary are general in nature and may not apply to all manufacturers’ systems. All terms in Section 3 apply to automotive inflatable restraint systems in general which are initiated by an electric or mechanical stimulus upon receipt of a signal from a sensor. These terms are intended to reflect existing designs and the Glossary will be updated as information on other types of systems becomes available. Appendix A is included to identify terminology that is no longer in common use or specifically applicable to inflatable restraint systems, but was published in the December 2001 version of SAE J1538.
This document lists recommended noun titles for drawings of support equipment and provides definitions for each. The use of secondary modifiers to distinguish a part from similar parts is also covered.
This specification includes detailed requirements for a fiber optic cable splice compliant with AS5405.
Counterfeiting of refrigerants has seen a dramatic rise over the past decades. This rise can be partially attributed to global restrictions placed on production and use of refrigerants by the 1987 Montreal Protocol, the 1997 Kyoto Protocol, and the 2016 Kigali Amendment to the Montreal Protocol [1, 2]. These protocols and the amendment regulate the gradual phase-out and strict regulations on the use of refrigerants with high Ozone Depletion Potential (ODP) and high Global Warming Potential (GWP). These protocols require that older refrigerants be replaced with more environmentally friendly products and necessitate redesigned, updated, or replaced equipment to operate efficiently with these new refrigerants.
This specification covers the general requirements for red and white individual instrument lights. This document has been streamlined. Appendix A to MIL-L-5057F lists those documents required for MIL-L-5057F acquisition and is a mandatory part of MIL-L-5057F. Those documents listed in Appendix A have the same status as those referenced directly in MIL-L-5057F (first tier documents). All other documents, referenced through tiering, may be used as guidance and information to supplement MIL-L-5057F. This document’s scope is limited to lamp source designs solely. Furthermore, the use of red lighting should not be considered for new design and included within this document to support requirements for existing military aircraft that still operate with this system of lighting.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7267 rubber. It shall be used for procurement purposes.
This SAE Aerospace Standard (AS) applies to a portable chemical oxygen generator assembly intended for the following uses: a First aid treatment of aircraft occupants after an emergency descent following a decompression or other emergency condition. b Use by cabin attendants to maintain their mobility after a decompression.
A life support system (LSS) is usually defined as a system that provides elements necessary for maintaining human life and health in the state required for performing a prescribed mission. The LSS, depending upon specific design requirements, will provide pressure, temperature, and composition of local atmosphere, food, and water. It may or may not collect, dispose, or reprocess wastes such as carbon dioxide, water vapor, urine, and feces. It can be seen from the preceding definition that LSS requirements may differ widely, depending on the mission specified, such as operation in Earth orbit or lunar mission. In all cases the time of operation is an important design factor. An LSS is sometimes briefly defined as a system providing atmospheric control and water, waste, and thermal management. The major subsystems required to accomplish the general functions mentioned above are: 1 Breathing and pressurization gas storage system. 2 Temperature and humidity control system. 3 Carbon dioxide
This recommended best practice outlines a method for estimating CO2-equivalent emissions using life cycle analysis.
This SAE Recommended Practice is applicable to gasoline and diesel fuel filters installed on fuel dispensing equipment, mobile or stationary. It describes a set of tests used to characterize the structural integrity, filtration performance, and reaction to water contaminant with fuel dispensing filters.
This specification covers the requirements for two types of oxygen pressure reducers.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings machined from AMS3650 material. It shall be used for procurement purposes.
Items per page:
50
1 – 50 of 221567