Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This procurement specification covers aircraft quality self-locking nuts for wrenching (hex, spline) and anchor (plate, gang channel, shank) types of nuts made from a corrosion and heat-resistant nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. Tension height nuts having overall length of threaded portion not less than 1.2 times the nominal thread diameter have 1210 MPa minimum tensile strength at room temperature. Shear height nuts having shorter threaded portion have 1100 MPa minimum tensile strength at room temperature. Maximum test temperature of parts is 730 Ā°C.
This document provides vehicle-level data collection, data analysis, and data verification procedures that may be used to verify that an instrument under test (IUT) satisfies the vehicle-level requirements specified in the SAE International (SAE) J2945/1 standard. For the purposes of this recommended practice, āvehicle-level requirementsā primarily consist of those requirements which can be verified external to the vehicle. The IUT for these procedures is a configured dedicated short range communications (DSRC) vehicle-to-vehicle (V2V) device as defined in SAE J2945/1 and is installed on a light vehicle. While the IUT is conceptually separated from the vehicle it is installed on, the tests outlined in this document are primarily vehicle-level so the terms āvehicleā and āIUTā can generally be considered interchangeable. Additionally, non-vehicle-level complementary tests, not included in this document, are required to verify that the entire set of requirements specified in SAE J2945/1
Primarily to provide recommendations concerning minimizing stress-corrosion cracking in wrought titanium alloy products.
Current regulations (e.g., Title 14 of the United States Code of Federal Regulations, or 14 CFR) define design requirements for oxygen system provisions for protection of crewmembers and passengers following emergency events such as in-flight decompression. This aerospace information report (AIR) addresses the operational oxygen system requirements for a decompression incident that may occur at any point during a long-range flight, with an emphasis for a decompression at the equal time point (ETP). This AIR identifies fuel and oxygen management contingencies and presents possible solutions for the efficient, safe, and optimum fuel/oxygen flight continuation. Oxygen management is a critical concern for all aircraft, ranging from single-engine types operating above 10000 feet to complex, high-performance aircraft equipped with supplemental oxygen systems. Proper planning ensures compliance with regulations and supports pilot and passenger safety at higher altitudes. This document
This document specifies dimensional, functional and visual requirements for Automotive grade coaxial cable. This material will be designated AG for general-purpose automotive applications or AG LL for low loss applications. It is the responsibility of the user of this cable to verify the suitability of the selected product (based on dimensional, mechanical, electrical and environmental requirements) for its intended application. It is the responsibility of the supplier to retain and maintain records as evidence of compliance to the requirements detailed in this standard.
The requirements of 9100 apply with the following clarification for software. This standard supplements the 9100 standard requirements for deliverable software and contains quality management system requirements for organizations that design, develop, and/or produce deliverable software and services for the aviation, space, and defense industry. This includes, as required, support software that is used in the development and maintenance of deliverable software and services. The deliverable software may be stand-alone, embedded, mobile application, or loadable into a target computer. This deliverable software may also be part of services (e.g., cloud environment, web hosted solutions or platforms). Where the use of Hardware Description Language (HDL) or high order language is utilized as the design source of electronic hardware [e.g., Application Specific Integrated Circuit (ASIC), Programmable Logic Device (PLD)]; the organization and customer, and/or supplier shall agree on the extent
This Surface Vehicle & Aerospace Recommended Practice offers best practices and a methodology by which IVHM functionality relating to components and subsystems should be integrated into vehicle or platform level applications. The intent of the document is to provide practitioners with a structured methodology for specifying, characterizing and exposing the inherent IVHM functionality of a component or subsystem using a common functional reference model, i.e., through the exchange of design-time data and the application of standard vehicle data communications interfaces. This document includes best practices and guidance related to the specification of the information that must be exchanged between the functional layers in the IVHM system or between lower-level components/subsystems and the higher-level control system to enable health monitoring and tracking of system degradation severity. The intent is to provide an IVHM system that can robustly report the degradation of a given
This SAE Standard for reliability-centered maintenance (RCM) is intended for use by any organization that has or makes use of physical assets or systems that it wishes to manage responsibly.
This SAE practice is intended for the sample preparation of test pieces for automotive wheels and wheel trim. The practice provides a consistent scribing method for use on test panels and or component parts with substrate chemical pretreatment and coating systems. Test specimens can then be subjected to various corrosion tests in order to evaluate performance without significant variations of the degree of exposure of the substrate. The scribing is used to create a break in the coating/finishing as can occur in the field through gravel and other damaging conditions. NOTEā Significant variability is attributed to surface contour, coating hardness/softness, operator reproducibility, and the scribing tool and itās condition.
This report is concerned with factors which affect accuracy of distance indication and speed indication of automotive type odometer speedometers. It is the intent to supply information regarding all items which affect the instrument.
Restricted hardenability steels have been in use for some time but the specific restrictions for a particular grade depend upon customer needs and vary from mill to mill. Such steels are desirable to provide more controlled heat treatment response and dimensional control for critical parts. Because of increasing interest in steels with restricted hardenability, the SAE Iron and Steel Technical Committee directed Division 8 to prepare a set of standard steels with restricted hardenability. In 1993, the American Society for Testing and Materials (ASTM) adopted the twelve SAE restricted hardenability steels and added ten more. SAE decided to include in SAE J1868 the additional 10 steels. In general, steels with restricted hardenability (RH steels) will exhibit a hardness range not greater than 5 HRC at the initial position on the end-quench hardenability bar and not greater than 65% of the hardness range for standard H-band steels (see SAE J1268) in the "inflection" region. Generally the
This SAE aerospace recommended practice (ARP) covers the requirements for external ground power equipment supplying 115/200 V, three-phase, 400 HZ output power measured at the aircraft receptacle. All forms of 400 Hz ground power including mobile and fixed systems are addressed by this document.
This interface standard applies to fuzes used in airborne weapons that use a 3-in fuze well. It defines: Physical envelope of the fuze well at the interface with the fuze. Load bearing surfaces of the fuze well. Physical envelope of the fuze and its connector. Mechanical features (e.g., clocking feature). Connector type, size, location and orientation. Retaining ring and its mechanical features (e.g., thread, tool interface). Physical envelope of the retaining ring at the interface with the fuze. Physical space available for installation tools. Torque that the installation tool shall be capable of providing. This standard does not address: Materials used or their properties. Protective finish. Physical environment of the weapon. Explosive interface or features (e.g., insensitive munitions (IM) mitigation). Charging tube. Torque on the retaining ring or loads on the load bearing surfaces. Each fuze and weapon combination should be evaluated to ensure that the weapon system will satisfy
This document covers all metal, castellated, self-locking nuts made from alloy steel of the types identified under the Unified Numbering System as UNS G41300 and UNS G43400.
Items per page:
50
1 ā 50 of 219833