Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE J2971 Recommended Practice describes a standard naming convention of aerodynamic devices and technologies used to control aerodynamic forces on trucks and buses weighing more than 10000 pounds (including trailers).
This specification covers an aluminum alloy in the form of sheet 0.125 to 0.249 inch (3.18 to 6.32 mm), inclusive, in nominal thickness (see 8.6).
This specification covers an aluminum alloy in the form of rolled or cold-finished bars, rods, and wire and of flash-welded rings and stock for flash-welded rings.
This specification covers an aluminum alloy in the form of welding wire.
This specification covers a leaded bronze in the form of sand and centrifugal castings (see 8.6).
This SAE Standard covers a single Un-Jacketed (UTP) and Jacketed (J-UTP) Balanced Unshielded Twisted Pair data cable intended for use in surface vehicle cables for 10 Mb/s Ethernet shared bus applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission.
This document is written to address acceleration and deceleration control issues related to heavy-duty trucks and buses greater than 10000 GVW.
This SAE Recommended Practice has been adopted by SAE to specify: a. A standard procedure for chassis dynamometer testing of heavy-duty road vehicles for the purpose of determining power delivered through the drive tires. b. A method of correcting observed power to reference test conditions. c. A method of analyzing the test data to determine if the test results are within expected power ranges.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of molded sheet 0.250 inch (6.35 mm) and under in nominal thickness.
This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of sheet, strip, and plate.
This SAE Aerospace Standard (AS) establishes the requirements for a V-band grooved clamp couplings that are intended for use on fluid-line tubing joints, tailpipe joints, and accessory mount joints, on flight vehicles or other attachments. The semi-rigid coupling joint assemblies, hereafter referred to as “the joint”, shall operate within the temperature ranges specified in their applicable part standards.
This specification covers an aluminum alloy in the form of sand, investment, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
This specification covers steel cleanliness requirements for premium aircraft-quality ferromagnetic steels, including hardenable, corrosion-resistant steels, by magnetic particle inspection methods. This specification contains sampling, sample preparation, inspection procedures, and cleanliness rating criteria (see 8.2).
This SAE Aerospace Recommended Practice (ARP) describes an industrial battery, lead-acid type, for use in electric powered ground support equipment.
This specification covers a copper-zinc alloy (brass) in the form of laminated sheet with nominal thickness 0.006 to 0.125 inch (0.15 to 3.18 mm) (see 8.5).
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Surface Vehicle Recommended Practice deals with electrostatic charge phenomena that may occur in automotive fuel systems and applies to the following: Fuels that are in a liquid state at ambient temperatures and atmospheric pressures and are contained in vehicle fuel tanks that operate at or near atmospheric pressure. This includes gasoline and diesel fuels, as well as their blends with additives such as alcohols, esters, and ethers, whether the additives are petroleum based or bio-fuel based. The group of components that comprise the fuel system (in contact and not in contact with fuels). Other components in proximity to the fuel system that may be affected by electrostatic fields caused by the fuel system. Electrostatic phenomena that arise from, or are affected by, the following aspects of vehicle or fuel system operation: Flowing fuel in the fuel delivery system. Flowing fuel being dispensed to the vehicle while it is being fueled.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up trucks with dual wheels, and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal to the driver of following (approaching a signaling vehicle from the rear) or oncoming (approaching a signaling vehicle from the front) vehicles over intervening vehicles.
This specification covers an aluminum alloy in the form of hand forgings up to 8 inches (203 mm), inclusive, in nominal thickness and a cross-sectional area not over 256 square inches (1652 cm2) and rolled rings up to 3.5 inches (89 mm), inclusive, in nominal thickness and with an OD to wall thickness ratio of 10:1 or greater (see 8.6).
This specification and its supplementary slash specifications establish the requirements for electrodeposition of metals by brush plating.
The purpose of this test is to evaluate the axial strength of the nut seat of wheels intended for use on passenger cars, light trucks, and multipurpose vehicles. In addition, a minimum contact area is recommended to ensure enough strength for the rotational force in tightening a nut against the nut seat. While this test ensures the minimum strength of the nut seat, the wheel must also have a degree of flexibility. This flexibility, as well as bolt tension, are important to maintain wheel retention.
This specification covers chromium-molybdenum (4130) seamless and welded steel tubing of aircraft quality.
Items per page:
50
1 – 50 of 215960