Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice establishes uniform procedures for testing BEVs that are capable of being operated on public and private roads. The procedure applies only to vehicles using batteries as their sole source of power. It is the intent of this document to provide standard tests that will allow for the determination of energy consumption and range for light-duty vehicles (LDVs) based on the federal test procedure (FTP) using the urban dynamometer driving cycle (UDDS) and the highway fuel economy driving schedule (HFEDS) and provide a flexible testing methodology that is capable of accommodating additional test cycles as needed. Additionally, this SAE Recommended Practice provides five-cycle testing guidelines for vehicles performing supplementary testing on the US06, SC03, and cold FTP procedures. Realistic alternatives should be allowed for new technology. Evaluations are based on the total vehicle system’s performance and not on subsystems apart from the vehicle.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate.
The scope of this SAE Recommended Practice is to promote compatibility between child restraint systems and vehicle seats and seat belts. Design guidelines are provided to vehicle manufacturers for certain characteristics of seats and seat belts and to child restraint system (CRS) manufacturers for corresponding CRS features so that each can be made more compatible with the other. The CRS accommodation fixture (see Figure 1) is used to represent a CRS to the designers of both the vehicle interior and the CRS for evaluation of each product for compatibility with the other. The features of the accommodation fixture are described as each is used.
Three levels of fan structural analysis are included in this practice: a Initial structural integrity. b In-vehicle testing. c Durability (laboratory) test methods. The initial structural integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The in-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The durability test methods section describes the detailed test procedures for a laboratory environment that may be used depending on type of fan, equipment availability, and end objective. The second and third levels build upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This specification covers a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
The published SAE J2954 standard established an industry-wide specification that defines acceptable criteria for interoperability, electromagnetic compatibility, EMF, minimum performance, safety, and testing for wireless power transfer (WPT) for light-duty plug-in electric vehicles. This SAE Information Report, SAE J2954/2, defines new power transfer levels in the higher power ranges needed for heavy-duty electric vehicles. This document addresses the requirements based on these charge levels and different vehicle applications as a first step in the process of completing a standard that the industry can use, both for private (fleet) and public wireless power transfer, including for charging electric vehicle batteries. This document is the first step in a process towards HD static and dynamic WPT. This document lacks specific requirements and solutions, for which field data is needed. This document is not intended to be a guideline to enable manufacturers to design systems with minimal
This SAE Recommended Practice provides test procedures, requirements, and guidelines for the system of optical warning devices used on emergency vehicles.
This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of light emitted by the device in any given direction, and not to the color of the light from a small area of the lens. It does not apply to pilot, indicator, or tell-tale lights.
This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for agricultural equipment.
This SAE Information Report J2931/6 establishes the requirements for physical and data link layer communications between Plug-in Electric Vehicles (PEV) and the Electric Vehicle Supply Equipment (EVSE).
This SAE Standard establishes test methods for the evaluation of devices and equipment in vehicles against transient transmission by coupling via lines other than the power supply lines. The test methods demonstrates the immunity of the instrument, device, or equipment to coupled fast transient disturbances, such as those caused by switching of inductive loads, relay contact bouncing, etc. Four test methods are presented in SAE J1113-12: the capacitive coupling clamp (CCC) method the direct capacitive coupling (DCC) method the inductive coupling clamp (ICC) method the capacitive/inductive coupling (CIC) method
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic, and communication equipment, and in interconnection systems.
This specification covers preforms fabricated up through 22.0 inches (560 mm), inclusive, in deposition width thickness (see 2.4) using a wire-fed plasma arc directed energy deposition (PA-DED) additive-manufacturing process on a Ti-6Al-4V substrate that are subjected to post-deposition stress-relief heat treatment. If required by the cognizant engineering organization (CEO), preforms may require subsequent machining to meet requirements for their intended final part application.
The AS81824 specification covers environment-resistant, permanent crimp type splices having heat shrinkable insulating sleeve and meltable environmental seals or heatless sealing sleeves. The splices may be used with tin, nickel, and silver-plated conductors in applications where the total temperature of the splice application does not exceed 200 °C or as specified in the detail specification.
Items per page:
50
1 – 50 of 216102