Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This SAE Aerospace Information Report (AIR) covers the general requirements for, and the listing of, manufacturers’ identification markings, names, symbols or trademarks, and CAGE codes that appear on electrical and electronic wiring devices and accessories as required by individual product specifications. Supplier markings from previous submitted listings are maintained for component traceability.
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing, or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test Almen strip holder is required for intensity determination.
This document is intended to establish a procedure to certify AD fallback test driver skill levels as an endorsement to SAE J3300 foundational level certification. The SAE J3300/3 endorsement can be used by the individual driver to qualify their skills as a test driver of vehicles with automated driving features. The SAE J3300/3 endorsement levels may also be used by test facilities or other organizations when seeking test or professional drivers with these skills. This document provides directions for obtaining the endorsement, including associated AD fallback test driving skill examination requirements, through SAE J3300-certified Examiners (refer to SAE J3300 for definition). Endorsement registration and associated records are administered through Probitas Authentication®. Probitas Authentication® is the current Independent Program Administrator for the SAE J3300 series. This document is a supplement to SAE J3300, providing information specific to the AD fallback test driver skill
This specification covers hollow glass microspheres.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
The technical architecture defined in this document outlines mandatory, emerging, and needed standards to provide interoperability at key interfaces in the aircraft/store system (including an associated NATO Network Enabled Capability environment), as required to support a future plug-and-play aircraft/store integration capability. These standards relate to services and protocols associated with the subject interfaces. Modeling standards to facilitate the Model Driven Architecture® (MDA®) approach to system definition and implementation are also included. Note that the status of referenced standards as reflected in this document is as of August 2007, and document users should check to see if there has been a subsequent change of status relative to applicable standards.
This document includes requirements of installations of adequate landing and taxiing lighting systems in aircraft of the following categories: a Single engine personal and/or liaison type b Light twin engine c Large multiengine propeller d Large multiengine turbojet/turbofan e Military high-performance fighter and attack f Helicopter This document will cover general requirements and recommended practices for all types of landing and taxi lights. More specific recommendations for LED lights in particular can be found in ARP6402.
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layers of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc. The purpose for applying an electroplate and the metals used for various
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the exhaust sound pressure levels of motorcycles under stationary conditions. Since initial publication, it has been successfully applied to regulation and monitoring of sound pressure levels of off-highway vehicles, and that remains its recommended application. Users of SAE J1287 for the purpose of roadside enforcement of sound pressure levels for on-highway motorcycles have reported difficulties with its implementation in that application. In response, SAE J2825 was developed, and is recommended for measurement of exhaust sound pressure levels of stationary on-highway motorcycles. Care must be taken not to confuse stationary sound pressure levels with total motorcycle sound pressure levels. This test does not evaluate total motorcycle sound during operation. For this purpose, SAE J331 or SAE J47 is recommended. Any allowable sound limits (dBA) set in relation to SAE J1287 for exhaust
This AIR provides a detailed example of the aircraft and systems development for a function of a hypothetical S18 aircraft. In order to present a clear picture, an aircraft function was broken down into a single system. A function was chosen which had sufficient complexity to allow use of all the methodologies, yet was simple enough to present a clear picture of the flow through the process. This function/system was analyzed using the methods and tools described in ARP4754A/ED-79A. The aircraft level function is “Decelerate Aircraft On Ground” and the system is the braking system. The interaction of the braking system functions with the aircraft are identified with the relative importance based on implied aircraft interactions and system availabilities at the aircraft level. This example does not include validation and verification of the aircraft level hazards and interactions with the braking system. However, the principles used at the braking system level can be applied at the
The intent of this standard is to establish a framework to assure that all evaporators conforming to its requirements demonstrate an acceptable health and safety environment for vehicle occupants as determined from the completed risk assessment. R-744 and low pressure (i.e., non-transcritical refrigerants with a critical temperature between 85 and 120 °C) mobile air conditioning (MAC) refrigerant evaporators shall meet the testing and labeling requirements of this standard. SAE J639 contains a list of all refrigerants considered acceptable for use in mobile thermal systems for which this standard applies when the refrigerant is used in a direct expansion architecture. SAE J639 also requires an assessment to be performed to minimize reasonable risks in MAC systems. The evaporator (as designed and manufactured) shall be part of that risk assessment, and it is the responsibility of the vehicle manufacturer to ensure all relevant aspects of the evaporator are included. It is the
SAE J1939-73 defines the SAE J1939 messages to accomplish diagnostic services and identifies the diagnostic connector to be used for the vehicle service tool interface. Diagnostic messages (DMs) provide the utility needed when the vehicle is being repaired. Diagnostic messages are also used during vehicle operation by the networked electronic control modules to allow them to report diagnostic information and self-compensate as appropriate, based on information received. Diagnostic messages include services such as periodically broadcasting active diagnostic trouble codes, identifying operator diagnostic lamp status, reading or clearing diagnostic trouble codes, reading or writing control module memory, providing a security function, stopping/starting message broadcasts, reporting diagnostic readiness, monitoring engine parametric data, etc. California-, EPA-, or EU-regulated OBD requirements are satisfied with a subset of the specified connector and the defined messages.
This test plan is broken into two major sections for the production testing of remote terminals: Electrical and Protocol.
Items per page:
50
1 – 50 of 222740