Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers piston rings fabricated from cast iron.
This document provides vehicle-level data collection, data analysis, and data verification procedures that may be used to verify that an instrument under test (IUT) satisfies the vehicle-level requirements specified in the SAE International (SAE) J2945/1 standard. For the purposes of this recommended practice, “vehicle-level requirements” primarily consist of those requirements which can be verified external to the vehicle. The IUT for these procedures is a configured dedicated short range communications (DSRC) vehicle-to-vehicle (V2V) device as defined in SAE J2945/1 and is installed on a light vehicle. While the IUT is conceptually separated from the vehicle it is installed on, the tests outlined in this document are primarily vehicle-level so the terms “vehicle” and “IUT” can generally be considered interchangeable. Additionally, non-vehicle-level complementary tests, not included in this document, are required to verify that the entire set of requirements specified in SAE J2945/1
This SAE Recommended Practice provides a system for marking thermoset rubber parts to designate the general type of material from which the part was fabricated.
This specification covers crimp-style aluminum lug terminals and conductor splices for aluminum aircraft wire. Lug terminals and conductor splices are hereafter called “terminals.”
This specification covers a titanium alloy in the form of bars up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2) and forging stock of any size (see 8.7).
This specification covers a corrosion-resistant steel in the form of investment castings homogenized and solution and precipitation heat treated to 130 ksi (895 MPa) tensile strength.
This specification covers a virgin, unfilled polytetrafluoroethylene (PTFE) in the form of extruded and sintered rods, tubes, and profiles.
The scope of this document is limited to encompass terminology, symbols, performance criteria and methods reflecting the current status of the technology.
This document specifies performance and quality requirements for the qualification and manufacture of 24 degree cone fittings to ensure reliable performance in aircraft hydraulic systems. This document specifies baseline criteria for the design and manufacture of system fittings that are qualification tested on engines. This document covers fittings of temperature types and pressure classes specified in MA2001.
This specification covers tantalum in the form of sheet, strip, plate, and foil up through 0.1875 inch (4.75 mm), inclusive (see 8.7).
This SAE Recommended Practice provides a common method to measure wear of friction materials (brake pad assemblies and brake shoes) and their mating parts (brake disc or brake drum). These wear measurements apply to brakes fitted on passenger cars and light trucks up to 4536 kg of Gross Vehicle Weight Rating under the Federal Motor Vehicle Safety Standard (FMVSS), or vehicles category M1 (passenger cars up to nine occupants, including the driver) under the European Community’s ECE Regulations.
This SAE Aerospace Standard (AS) defines a series of standardized tube walls to be used for high pressure hydraulic tubing. These tube walls are applicable to all homogenous tube materials (i.e., aluminum, steel, titanium) throughout a rated pressure range of 1000 to 8000 psi and a maximum rated operating temperature range of 160 to 450 °F. All future aerospace applications for which a required tube outside diameter/tube wall combination is not presently available shall be selected from the table contained herein (see Figure 1).
This SAE Aerospace Information Report (AIR) has been compiled to provide information on hydraulic systems fitted to the following categories of military vehicles. Attack Airplanes Fighter Airplanes Bombers Anti-Sub, Fixed Wing Airplanes Transport Airplanes Helicopters Boats
This SAE Aerospace Recommended Practice (ARP) provides recommended solid film lubricants for use on fluid system components at different temperatures and cyclic conditions.
This document defines the requirements for weld fittings and machine weldments using an orbiting welding head suitable for use on cold worked 3AL-2.5V titanium, 21Cr-6Ni-9Mn CRES, and 718 nickel alloy tubing. Fitting standards covered by this specification include non-separable welded elbow, tee, and reducer fittings, and reconnectable 24-degree cone fittings, such as sleeves and unions.
This specification establishes the requirements for an expanded polytetrafluoroethylene (ePTFE) in the form of sealing tape, gaskets, or sheets requiring no mixing or curing.
SCOPE IS UNAVAILABLE.
The purpose of this SAE Standard is to establish the specific minimum equipment performance requirements for recovery and recycling of HFC-134a that has been directly removed from, and is intended for reuse in, mobile air-conditioning (A/C) systems. It also is intended to establish requirements for equipment used to recharge HFC-134a to an accuracy level that meets Section 9 of this document and SAE J2099. The requirements apply to the following types of service equipment and their specific applications: a. Recovery/recycling equipment b. Recovery/recycling - refrigerant charging c. Refrigerant recharging equipment only
SCOPE IS UNAVAILABLE.
This SAE Standard provides requirements and guidance to: Develop a Materiel authenticity plan. Procure Materiel from reliable sources. Assure authenticity and conformance of procured Materiel, including methods such as certification, traceability, testing, and inspection appropriate to the Commodity/item in question. Control Materiel identified as counterfeit. Report Suspect or Counterfeit Materiel to other potential users and Authorities Having Jurisdiction.
This ARP provides definitions and background information regarding the physical performance and testing of DDVs. This ARP also provides extensive guidance for the preparation of procurement specifications and functional testing.
This SAE Aerospace Information Report (AIR) has been prepared to provide information regarding options for optical control of fluid power actuation devices. It is not intended to establish standards for optical fluid power control, but rather is intended to provide a baseline or foundation from which standards can be developed. It presents and discusses approaches for command and communication with the actuation device via electro-optic means. The development of standards will require industry wide participation and cooperation to ensure interface commonality, reliability, and early reduction to practice. To facilitate such participation, this document provides potential users of the technology a balanced consensus on its present state of development, the prospects for demonstration of production readiness, and a discussion of problem areas within this technology. The intent is to inform the user/designer of the options available for interfacing photonics (optics) to hydraulic power
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design and installation of a commercial aircraft hydraulic system to meet the applicable requirements, including the applicable airworthiness regulations that affect the hydraulic system design. This ARP also provides information and guidelines on the many factors that arise in the design process to provide cost effectiveness, reliability, maintainability and accepted design and installation practices.
This specification covers the design requirements and test procedures for separable beam seal fittings which include end fittings (see 2.4.2), connectors (see 2.4.3), and boss fittings for use in aerospace fluid systems. Design requirements are for Class 5000 and 8000 in titanium, and corrosion resistant steel (CRES). Definition of fittings and related terms are defined in 2.4.
This SAE Aerospace Information Report (AIR) includes all missile and launch vehicle actuation systems, including electrohydraulic, electropneumatic, and electromechanical types. The data for many systems are not complete. As more information becomes available, periodic updates will be issued to complete existing data sheets and to add new ones. An index by type of vehicle and by type of actuation system is included. The actual data sheets in the body of the report are organized in alphabetical order.
These requirements are applicable to IAQG sector schemes when making use of ABs, CRBs and their auditors, for the assessment and certification/registration of supplier quality systems in accordance with the requirements of this document. The quality management system standard used by the CRB shall be 9100/9110/9120, as appropriate to the supplier’s activities. It shall be applied to the supplier’s complete Quality System that covers aerospace products. Sectors may use these requirements for other standards. IAQG members have committed to recognize the equivalence of certification/registration of a suppliers quality management system to either of the AS, EN or JISQ/SJAC standards. This AS provides the approval process for Auditor Authentication Bodies (AAB), training course providers, trainers and auditors who meet the requirements of AIR5493 and outlines the America’s sector specific process to implement AS9104. This document is created to be in conformance with AS9104.
Items per page:
50
1 – 50 of 215848