Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This specification covers established manufacturing tolerances applicable to low-alloy steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of the specified range.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS2759. Due to limited hardenability in these materials, there are size limits in this specification.
This specification covers an aluminum alloy in the form of castings (see 8.6).
To define a list of anomalies related to OBD Communications. Misinterpretations of various OBD Communications Standards and Recommended Practices have resulted in OBD “no-communications” situations in the field. This Information Report identifies the most prevalent of these.
This specification covers an aluminum alloy in the form of sheet, clad on one side.
This specification covers a carbon steel in the form of sheet and strip.
This specification covers a premium aircraft-quality alloy steel in the form of bars and forgings 199 square inches (1284 cm2) and under in cross section, and forging stock of any size.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers an aircraft-quality, low-alloy, heat-resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Aerospace Recommended Practice (ARP) provides recommendations for design and test requirements for a generic “passive” side stick that could be used for fly-by wire transport and business aircraft. It addresses the following: The functions to be implemented The geometric and mechanical characteristics The mechanical and electrical interfaces The safety and certification requirements
This Aerospace Recommended Practice aims at providing general utilization guidelines and calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements performed to restrain cargo on board civil transport aircraft during flight: a Cargo loaded and tied down onto airworthiness approved air cargo pallets, themselves restrained into aircraft lower deck, main deck or upper deck cargo systems meeting the restraint requirements of air cargo pallets approved in accordance with NAS 3610 or AS36100, or b Additional tie-down on aircraft structure when necessitated by pallet maximum gross mass or centre of gravity location, or c Individual pieces of cargo, or pieces of cargo placed onto an unrestrained (“floating”) pallet into either lower deck, main deck or upper deck containerized cargo compartments of an aircraft, or d Individual pieces of load loaded in non-containerized (bulk loaded) baggage or cargo compartments.
Scope is unavailable.
This SAE Aerospace Information Report (AIR) has been written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in upgrading their existing or acquiring new test cell facilities.
This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall tubing.
This SAE Aerospace Recommended Practice (ARP) specifies for quality requirements that are additive to a procurement document or contract, where an organization: a needs to provide additional guidance for suppliers and other organizations in the delivery of products, goods and services in accordance with stated quality demands, and b needs to provide information in addition or in absence of existing quality system requirements to provide the assurance of conformity to customer and applicable regulatory requirements. NOTE: In this ARP, the term ‘product’ applies only to the product intended for, or required by, a customer.
This recommended practice provides the design criteria for static elastomeric O-ring seals used specifically in engine and engine control systems. It provides axial compression (face type) groove dimensions for aerospace metric O-ring sizes specified in MA2010. The conditions considered to formulate the design criteria are also described, e.g., seal squeeze and groove volume to accommodate O-ring swell. NOTE: Tables of O-ring groove dimensions are included based on the design criteria specified herein. Dimensions in this document are in millimeters unless otherwise specified.
This document is intended for use by manufacturers of aircraft, engines and Electronic Engine Controls [EECs] as a component change process and evaluation guideline. Its purpose is to provide an effective means of managing the modification of electronic hardware. The process defined in this document is based upon: an understanding of the electronic component market evolution, e.g., obsolescence; lessons learned from the effects caused by the introduction of electrical component changes in a service fleet environment; industry best practice; and an understanding of the applicable regulations.
This SAE Recommended Practice provides a uniform procedure and performance requirements for evaluating fastening systems for normal highway use on aftermarket passenger cars and light trucks (except dual wheels, which are covered by SAE J1965) and multipurpose passenger vehicles. The fastening system includes the wheel, wheel bolts, and wheel nuts, as well as vehicle mating surface. The coefficients of friction for steel and aluminum mating surfaces are provided based on information available. Many factors must be considered in design and validation of wheel attachments for each specific vehicle. Where the procedure is used for original equipment applications the vehicle manufacturers specifications supersede those noted.
This specification defines the requirements for locally hardening steel parts by the induction hardening method.
This specification establishes general requirements for the processes listed in 3.8.1 for heat treatment of steel parts (see 8.2.1) by users or their vendors or subcontractors.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
Items per page:
50
1 – 50 of 219833