Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This SAE Recommended Practice defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.
This SAE Standard provides the minimum requirements for high-power, two-conductor jumper cable plug and receptacle for truck-trailer jumper cable systems. It includes the test procedures, design, and performance requirements. This document covers receptacles rated 12 VDC nominal and at more than 30 A (amperes) up to and including 150 A, and is intended for a single circuit with one power conductor and one common return conductor. Single-conductor high-current connectors are not recommended for future designs because of inadequate ground return through fifth wheel/king pin. Cable size selection is to be made by the vehicle OEM for specific applications and the specific voltage drop requirements of those applications. This SAE Standard covers two variants of high-power two-conductor connections: a heavy duty version, with horizontally aligned pins, typically for lift-gate battery charging; and a medium duty version, with vertically aligned pins, typically for loads such as power
This specification covers a carbon steel in the form of strip.
This method is intended to define the continuous upper temperature limit (CUTL) of thermoplastic elastomers and thermoset rubber with durometer hardness <=90 Shore A, to oxidation or other degradation when exposed solely to hot air for an extended period of time.
This specification covers an aluminum alloy powder metallurgy product in the form of sheet 0.010 to 0.250 inch (0.25 to 6.35 mm) in nominal thickness.
This specification covers a premium aircraft-quality steel in the form of bars, forgings, mechanical tubing, flash welded rings up through 10.000 inches (254.00 mm) inclusive in diameter or least distance between parallel sides, and stock of any size for forging or flash welded rings.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This document describes a physical layer utilizing Unshielded Twisted Pair (UTP) cable with extended stub lengths for flexibility in ECU placement and network topology. Also, connectors are not specified. CAN controllers used on SAE J1939-15 networks must be restricted to use only Classical Frames as defined in ISO 11898- 1. A network which may have legacy controllers cannot tolerate FD Frames. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
This SAE Aerospace Standard (AS) defines implementation requirements for the electrical interface between: a Aircraft carried miniature store carriage systems and miniature stores b Aircraft parent carriage and miniature stores c Surface-based launch systems and miniature stores The interface provides a common interfacing capability for the initialization and employment of smart miniature munitions and other miniature stores from the host systems. Physical, electrical, and logical (functional) aspects of the interface are addressed.
This SAE Information Report establishes a consistent procedure for measuring and analyzing the natural sway response of a particular trailer when attached to a particular vehicle under specific loading and operating conditions. This test procedure applies, but is not limited to, passenger cars, vans, light/medium-duty trucks as tow vehicles, and semitrailers with a Gross Vehicle Weight Rating (GVWR) of 11794 kg (26000 pounds) or less. Other applications include full trailers, tow dollies, tow bars, and the like. Other articulated vehicles can utilize this test procedure as long as the test does not exceed the linear behavior of the system. This test procedure does not apply to motorcycles towing trailers.
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self-propelled work machines as defined by SAE J1116 (limited to categories of (1) construction, and (2) general purpose industrial).
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
The Class A Task Force of the Vehicle Network for Multiplexing and Data Communications Subcommittee is providing information on sensors that could be applicable for a Class A Bus application. Sensors are generally defined as any device that inputs information onto the bus. Sensors can be an input controlled by the operator or an input that provides the feedback or status of a monitored vehicle function. Although there is a list of sensors provided, this list is not all-inclusive. This SAE Information Report is intended to help the network system engineer and is meant to stimulate the design thought process.
This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an identifier. The standard describes a unique identification and the associated data set for each tire produced by the tire fabricator. This data will either be provided or transmitted at the time of shipment to retailers, wholesalers or original equipment vehicle manufacturers. Tire identification code and data may be used for error proofing, determining the tire specifications or supporting any inquiries that occur for the duration of its automotive life.
This specification, in conjunction with the general requirements for steel heat treatment in AMS2759, establishes requirements for thermal stress-relief treatments of parts manufactured from the following materials: a Carbon and low-alloy steels b Tool steels c Precipitation-hardening, corrosion-resistant, and maraging steels d Austenitic corrosion-resistant steels e Martensitic corrosion-resistant steels
This specification establishes requirements for steel forgings of any shape or form from which finished parts are to be made (See 8.2, 8.3, & 8.4). This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment
This specification covers a low-carbon steel in the form of bars, forgings, mechanical tubing, and forging stock.
This interface standard applies to fuzes used in airborne weapons that use a 3-in fuze well. It defines: Physical envelope of the fuze well at the interface with the fuze. Load bearing surfaces of the fuze well. Physical envelope of the fuze and its connector. Mechanical features (e.g., clocking feature). Connector type, size, location and orientation. Retaining ring and its mechanical features (e.g., thread, tool interface). Physical envelope of the retaining ring at the interface with the fuze. Physical space available for installation tools. Torque that the installation tool shall be capable of providing. This standard does not address: Materials used or their properties. Protective finish. Physical environment of the weapon. Explosive interface or features (e.g., insensitive munitions (IM) mitigation). Charging tube. Torque on the retaining ring or loads on the load bearing surfaces. Each fuze and weapon combination should be evaluated to ensure that the weapon system will satisfy
The scope of this document is to aid in the selection of hose and hose assembly titles.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers a maraging steel in the form of welding wire.
This specification covers an aluminum alloy in the form of sheet clad on both sides with a different aluminum alloy.
This specification covers the specific requirements for 7075 aluminum alloy alclad one side plate and sheet; the general requirements are covered in AMS-QQ-A-250. The plate and sheet covered by this specification shall be an integral composite product consisting of a heat-treatable aluminum alloy (7075) core with a thin layer of an aluminum alloy (7072) anodic to the core bonded to one surface.
Items per page:
50
1 – 50 of 221567