Results
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
This document is intended to establish a procedure to certify AD fallback test driver skill levels as an endorsement to SAE J3300 foundational level certification. The SAE J3300/3 endorsement can be used by the individual driver to qualify their skills as a test driver of vehicles with automated driving features. The SAE J3300/3 endorsement levels may also be used by test facilities or other organizations when seeking test or professional drivers with these skills. This document provides directions for obtaining the endorsement, including associated AD fallback test driving skill examination requirements, through SAE J3300-certified Examiners (refer to SAE J3300 for definition). Endorsement registration and associated records are administered through Probitas Authentication®. Probitas Authentication® is the current Independent Program Administrator for the SAE J3300 series. This document is a supplement to SAE J3300, providing information specific to the AD fallback test driver skill
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This SAE Aerospace Information Report (AIR) covers the general requirements for, and the listing of, manufacturers’ identification markings, names, symbols or trademarks, and CAGE codes that appear on electrical and electronic wiring devices and accessories as required by individual product specifications. Supplier markings from previous submitted listings are maintained for component traceability.
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing, or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test Almen strip holder is required for intensity determination.
SAE J1939-2 specifies the requirements for application of SAE J1939 in agricultural and forestry equipment. This document specifies the series of documents within the set of SAE J1939 documents that are applicable to agricultural and forestry equipment and provides further requirements for this industry. The SAE and ISO groups have cooperated to define agricultural and forestry networks in a manner to allow compatibility of ECUs and messaging protocols between the A&F and the T&B networks.
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7274 rubber. It shall be used for procurement purposes.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene, (PCTFE) in the form of thin wall tubing.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This interface standard applies to fuzes/fuzing systems (referred to as fuzing system hereafter) in airborne weapons that use a MIL-STD-1760 type interface. It defines the powers, the discrete signals and the serial data interface for the communications at the interface between the fuzing system and the remainder of the weapon, including the weapon control unit. The Class 1 interface is an electrical only interface that facilitates use of MIL-STD-1760 type platform store interfaces for the fuze to monitor intentional release and defines the fuze interface bus communications protocol to allow sending and receiving data from fuzing systems. Class 2 interfaces add a defined connector and additional interfaces to facilitate the exchange of compatible fuzing systems. Class 3 interfaces add further interface definitions to facilitate the exchange of AS5680A compatible fuzing systems components. The bus communications protocol provides a means by which the weapon may set mission parameters
This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
Scope is unavailable.
The purpose of this SAE Aerospace Standard is to provide guidelines for the components and configurations that define the research and commercial versions of the Weather Support to Deicing Decision Making (WSDDM) winter weather nowcasting system.
This SAE Surface Vehicle Information Report identifies and defines the drawings and parts relating to the use of the Hybrid III Large Male Test Dummy.
This specification covers a corrosion and heat resistant work strengthened nickel alloy in the form of bars and wire, 1½ inches (38 mm) and under in nominal diameter (See 8.2).
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement fault-tolerant CAN (FT CAN) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/8_0500 interface shall be compliant to fault-tolerant CAN (FT CAN) feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, and components. Said actuators are used for applying cam type foundation brakes by slack adjuster means.
The test procedures outlined in this SAE Standard are applicable to turbocharging systems having either fixed- or variable-geometry.
This SAE Aerospace Recommended Practice (ARP) establishes the overall component and system function guidelines and minimum performance levels for a TPMS. These guidelines include, but are not limited to: Design recommendations for system components, which: Monitor tire inflation Are located in/on the tire/wheel assembly, landing gear axle, and/or aircraft avionics compartment Recommended performance and safety guidelines for a TPMS.
Items per page:
50
1 – 50 of 222501