Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This specification covers a corrosion-resistant steel in the form of investment castings homogenized and solution and precipitation heat treated to 180 ksi (1241 MPa) tensile strength.
This specification covers three types of aircraft position lights.
This specification covers materials in the form of a liquid used to remove smut from aluminum surfaces treated with etch-type oxidation and corrosion removers.
This procurement specification covers solid rivets and hollow end rivets made from a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286 and of 80 ksi single shear strength at room temperature.
“An Assessment of Planar Waves” provides background on some of the history of planar waves, which are time-dependent variations of inlet recovery, as well as establishing a hierarchy for categorizing various types of planar waves. It further identifies approaches for establishing compression-component and engine sensitivities to planar waves, and methods for accounting for the destabilizing effects of planar waves. This document contains an extensive list and categorization (see Appendix A) of references to aid both the newcomer and the practitioner on this subject. The committee acknowledges that this document addresses only the impact of planar waves on compression-component stability and does not address the impact of planar waves on augmenter rumble, engine structural issues, and/or pilot discomfort.
This specification covers a two-component compound, an epoxy resin base and a hardener, in the form of a paste.
This specification covers a copper-nickel-tin alloy in the form of bars and rods.
This specification covers an aluminum alloy in the form of sheet laminated with two or more layers of unidirectional aramid fiber/epoxy prepreg.
This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, and plate.
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This AIR was prepared to inform the aerospace industry about the electromagnetic interference measurement capability of spectrum analyzers. The spectrum analyzers considered are of the wide dispersion type which are electronically tuned over an octave or wider frequency range. The reason for limiting the AIR to this type of spectrum analyzer is that several manufacturers produce them as general-purpose instruments, and their use for EMI measurement will give significant time and cost savings. The objective of the AIR is to give a description of the spectrum analyzers, consider the analyzer parameters, and describe how the analyzers are usable for collection of EMI data. The operator of a spectrum analyzer should be thoroughly familiar with the analyzer and the technical concepts reviewed in this AIR before performing EMI measurements.
This specification covers established inch/pound manufacturing tolerances applicable to carbon steel sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term “excl” is used to apply only to the higher figure of the specified range. Tolerances for product sizes not listed herein shall be as agreed upon by purchaser and vendor.
This specification covers tubular-shaped pins, fabricated from carbon steel, having a full-length longitudinal slot to permit flexure when inserted into a hole.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement SAE J1708 within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/6_0500 interface shall be compliant to the SAE J1708 feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This document specifies dimensional, functional and visual requirements for Automotive grade coaxial cable. This material will be designated AG for general-purpose automotive applications or AG LL for low loss applications. It is the responsibility of the user of this cable to verify the suitability of the selected product (based on dimensional, mechanical, electrical and environmental requirements) for its intended application. It is the responsibility of the supplier to retain and maintain records as evidence of compliance to the requirements detailed in this standard.
This specification covers the requirements for self-sealing, quick-disconnect couplings for fuel and oil system components.
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers aluminum alloy die forgings and hand forgings.
This SAE Standard provides test procedures, performance requirements and guidelines for auxiliary high beam lamps.
Items per page:
50
1 – 50 of 221567