Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice establishes uniform procedures for testing BEVs that are capable of being operated on public and private roads. The procedure applies only to vehicles using batteries as their sole source of power. It is the intent of this document to provide standard tests that will allow for the determination of energy consumption and range for light-duty vehicles (LDVs) based on the federal test procedure (FTP) using the urban dynamometer driving cycle (UDDS) and the highway fuel economy driving schedule (HFEDS) and provide a flexible testing methodology that is capable of accommodating additional test cycles as needed. Additionally, this SAE Recommended Practice provides five-cycle testing guidelines for vehicles performing supplementary testing on the US06, SC03, and cold FTP procedures. Realistic alternatives should be allowed for new technology. Evaluations are based on the total vehicle system’s performance and not on subsystems apart from the vehicle.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate.
The scope of this SAE Recommended Practice is to promote compatibility between child restraint systems and vehicle seats and seat belts. Design guidelines are provided to vehicle manufacturers for certain characteristics of seats and seat belts and to child restraint system (CRS) manufacturers for corresponding CRS features so that each can be made more compatible with the other. The CRS accommodation fixture (see Figure 1) is used to represent a CRS to the designers of both the vehicle interior and the CRS for evaluation of each product for compatibility with the other. The features of the accommodation fixture are described as each is used.
Three levels of fan structural analysis are included in this practice: a Initial structural integrity. b In-vehicle testing. c Durability (laboratory) test methods. The initial structural integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The in-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The durability test methods section describes the detailed test procedures for a laboratory environment that may be used depending on type of fan, equipment availability, and end objective. The second and third levels build upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This specification covers a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1100) condition, 12 inches (305 mm) and under in nominal diameter, thickness, or, for hexagons, least distance between parallel sides. The aged product may be supplied directly by a producer or by another entity performing the functions of a producer as defined in AS6279. The latter can be accomplished by precipitation heat treatment of solution treated material previously certified to AMS5934. The entity assuming responsibility for the aging operation is designated the producer of AMS5934/H1100.
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness, or for hexagons, least distance between parallel sides in the solution and precipitation heat treated (H1050) condition.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 12 inches (305 mm) and under in nominal diameter, thickness, or, for hexagons, least distance between parallel sides.
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides in the solution and precipitation heat treated (H1150) condition.
This specification covers a low-alloy steel in the form of investment castings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet and strip 0.080 inch (2.03 mm) and under in nominal thickness.
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 64 in2 (413 cm2) in the solution and precipitation heat treated (H1075) condition
This specification covers polyurethane (PUR) in the form of two-component sealing compounds.
This specification covers a titanium alloy in the form of bars, wire, forgings up to 4.000 inches (101.60 mm), inclusive, and forging stock.
AMS6885/1 gives information about the technical requirements and qualification procedure for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The repair system includes an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy in the form of hand forgings up to 8 inches (203 mm), inclusive, in nominal thickness and a cross-sectional area not over 256 square inches (1652 cm2) and rolled rings up to 3.5 inches (89 mm), inclusive, in nominal thickness and with an OD to wall thickness ratio of 10:1 or greater (see 8.6).
This specification covers an aluminum alloy in the form of wire, sheet, foil, pig, grains, shot, and chips (see 8.6).
This specification covers an aluminum alloy in the form of die forgings from over 2.000 to 10.000 inches (50.8 to 254 mm) in nominal thickness and forging stock of any size (see 8.6).
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This specification covers engineering requirements for applying tungsten carbide thermal spray coatings to ultrahigh-strength steels (220 ksi and above) utilizing high-velocity oxygen fuel (HVOF) combustion-driven processes and the properties for such coatings. The processes and procedures herein apply only to the properties of the as-deposited coating.
This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings up to 8.0 inches (203 mm) in diameter or least distance between parallel sides in the solution heat-treated condition (see 8.4), and stock of any size for forging, flash-welded rings, or heading.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in nominal thickness at the time of heat treatment and having an OD to wall thickness ratio of 10 or greater (see 8.6).
Items per page:
50
1 – 50 of 216102