Results
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This specification covers a premium aircraft-quality alloy steel in the form of bars, forgings, and forging stock.
This SAE Aerospace Information Report (AIR) provides data and general analysis methods for calculation of internal and external, pressurized and unpressurized airplane compartment pressures during rapid discharge of cabin pressure. References to the applicable current FAA and EASA rules and advisory material are provided. While rules and interpretations can be expected to evolve, numerous airplanes have been approved under current and past rules that will have a continuing need for analysis of production and field modifications, alterations and repairs. The data and basic principles provided by this report are adaptable to any compartment decompression analysis requirement.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers the requirements for the acquisition of two alloys of copper-beryllium alloy strip, having higher electrical conductivity than copper-beryllium alloy strip normally used (see 6.1). All sizes of strip are covered by this specification.
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layers of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc. The purpose for applying an electroplate and the metals used for various
The Gauge Evaluation Procedure Task Force was formed by the Non-Hydraulic Hose Committee to develop a gauge evaluation procedure to be used when evaluating the capability of gauges used for hose measurement. The use of a standard method for gauge evaluation will help users easily compare equipment capability. The information provided in this recommendation is based on the methods used to produce the data presented in SAE J1759 and J2605.
This standard provides background information and a hydrogen fuel quality standard for commercial proton exchange membrane (PEM) fuel cell electric vehicles. This standard also provides background information on how it was developed by the Interface Task Force (ITF) of the SAE Fuel Cell Standards Committee.
The function of a multifunctional display (MFD) system is to provide the crew access to a variety of data, or combinations of data, used to fly the aircraft, to navigate, to communicate, and to manage aircraft systems. MFDs may also display primary flight information (PFI) as needed to insure continuity of operations. This document sets forth design and operational recommendations concerning the human factors considerations for MFD systems. The MFD system may contain one or more electronic display devices capable of presenting data in several possible formats. MFDs are designed to depict PFI, navigation, communication, aircraft state, aircraft system management, weather, traffic, and/or other information used by the flight crew for command and control of the aircraft. The information displayed may be combined to make an integrated display or one set of data may simply replace another. The information contained in this document can be applied to the design of all MFDs, including
This SAE Aerospace Recommended Practice (ARP) describes standard methods of heat application to cure thermosetting resins for commercial aircraft composite repairs. The methods described in this document shall only be used when specified in an approved repair document or with the agreement of the Original Equipment Manufacturer (OEM) or regulatory authority.
This SAE Aerospace Information Report presents a glossary of terms commonly used in the ground delivery of fuel to an aircraft and pertinent terms relating to the aircraft being refueled.
This SAE Aerospace Recommended Practice (ARP) establishes the guidelines for selection of titles of aerospace fitting documents generated by SAE Subcommittee G-3B.
This specification covers a corrosion and heat resistant steel in the form of welding wire.
The objective of this ARP is to provide a set of user-centered design guidelines for the implementation of data driven electronic aeronautical charts, which dynamically create charts from a database of individual elements. The data driven chart is intended to provide information required to navigate, but it is not intended to supplant the aircraft’s primary navigation display. These guidelines seek to provide a balance between standardization of equipment with similar intended functions and individual manufacturer innovation. This ARP provides guidelines for the display of an electronic chart that can replace existing paper. This document addresses what information is required, when it is required, and how it should be displayed and controlled. This document does not include all the detailed specifications required to generate an electronic aeronautical chart. This document primarily addresses the human factors aspects of electronic chart display, and does not address the software
This specification covers a premium aircraft-quality, maraging steel in the form of sheet, strip, and plate.
This SAE Aerospace Recommended Practice (ARP) covers specification requirements for a rotary plow with carrier vehicle. The primary use is to cast heavy concentrations of snow approximately perpendicular to carrier vehicles across and away from airport operational areas, such as runways and taxiways. Rotary plows equipped with spot casting, or loading chutes are also used to cast snow in directions through approximately 100 degrees to the left or right of directly in front of the carrier vehicle, and also to load trucks or trailers used to haul snow away from removal area. The term “carrier vehicle” represents the various self-propelled prime movers that provide the power necessary to move snow and ice control equipment during winter operations.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
Items per page:
50
1 – 50 of 220391