Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
This SAE Recommended Practice defines the set-up and procedure for conducting the SAE Single Tooth Bending Fatigue Test. The details of the test fixture to be used (referred henceforth as “the test fixture” in this document) and gear test sample and the procedures for testing and analyzing the data are presented in this document.
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
This specification covers an aluminum alloy powder metallurgy product in the form of round extrusions up to 3.5 inches (89 mm) in diameter and rectangular and other solid extrusions up to 10 square inches (64.5 cm2) in cross-sectional area. The maximum extrusion length is 100 inches (2.5 m).
This test method outlines the recommended machine function, fixtures, and procedures used to test airframe rolling element bearings for dynamic performance under steady unidirectional radial load and oscillatory motion. Bearings covered by this test method shall be ball, roller, or needle type in either annular or rod end configuration, used in airframe control applications.
This specification covers a magnesium alloy in the form of sand castings.
MIL-STD-1553 establishes requirements for digital command/response time division multiplexing (TDM) techniques on military vehicles, especially aircraft. The existing MIL-STD-1553 network operates at a bit rate of 1 Mbps and is limited by the protocol to a maximum data payload capacity of approximately 700 kilobits per second. The limited capacity of MIL-STD-1553 buses coupled with emerging data rich applications for avionics platforms plus the expense involved with changing or adding wires to thousands of aircraft in the fleet has driven the need for expanding the data carrying capacity of the existing MIL-STD-1553 infrastructure.
This specification establishes requirements for steel forgings of any shape or form from which finished parts are to be made (See 8.2, 8.3, & 8.4). This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment
This specification establishes general requirements for the processes listed in 3.8.1 for heat treatment of steel parts (see 8.2.1) by users or their vendors or subcontractors.
This SAE Aerospace Recommended Practice (ARP) defines a means of assessing the credibility of computer models of aircraft seating systems used to simulate dynamic impact conditions set forth in Title 14, Code of Federal Regulations (14 CFR) Parts 23.562, 25.562, 27.562, and 29.562. The ARP is applicable to lumped mass and detailed finite element seat models. This includes specifications and performance criteria for aviation specific virtual anthropomorphic test devices (v-ATDs). This document provides a recommended methodology to evaluate the degree of correlation between a seat model and dynamic impact tests. This ARP also provides best practices for testing and modeling designed to support the implementation of analytical models of aircraft seat systems. Supporting information within this document includes procedures for the quantitative comparison of test and simulation results, as well as test summaries for data generated to support the development of v-ATDs and a sample v-ATD
This standard covers oronasal type masks which use a continuous flow oxygen supply. Each such mask comprises a facepiece with valves as required, a mask suspension device, a reservoir, or rebreather bag (when used), a length of tubing for connection to the oxygen supply source, and a means for allowing the crew to determine if oxygen is being delivered to the mask. The assembly shall be capable of being stowed suitably to meet the requirements of its intended use.
This specification covers a low-alloy steel in the form of welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This specification covers a corrosion-resistant steel in the form of welding wire.
This specification covers a premium aircraft-quality, high-alloy tool steel gas-atomized and HIP-consolidated in the form of bars, wire, forgings, and forging stock.
This document provides recommendations to identify battery group sizes and dimensions for 6 V, 8 V, 12 V, and 24 V lead acid batteries.
This document covers all metal, castellated, self-locking nuts made from alloy steel of the types identified under the Unified Numbering System as UNS G41300 and UNS G43400.
The Class A Task Force of the Vehicle Network for Multiplexing and Data Communications Subcommittee is providing information on sensors that could be applicable for a Class A Bus application. Sensors are generally defined as any device that inputs information onto the bus. Sensors can be an input controlled by the operator or an input that provides the feedback or status of a monitored vehicle function. Although there is a list of sensors provided, this list is not all-inclusive. This SAE Information Report is intended to help the network system engineer and is meant to stimulate the design thought process.
This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 °F. Gaseous service shall be limited to 150 °F.
Items per page:
50
1 – 50 of 222741