Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing.
This specification covers a one-part fluorosilicone (FVMQ) adhesive/sealant, supplied in cartridges, suitable for extrusion and curing to an elastomeric material upon exposure to air. It also covers a compatible primer.
This procurement specification covers tubular, blind rivets fabricated from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04405, and of 52 ksi minimum shear strength for self-plugging style rivets.
This specification and its supplementary detail specifications covers organic fibers in the form of continuous, multifilament yarn and roving.
This specification covers a silicone rubber in the form of a two-component liquid compound.
This specification covers a silicone, electrically conductive and corrosion-inhibiting sealing compound.
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-rings with a coded part number.
This specification covers a direct reading, remote control, pneumatic pressure inflator assembly, for use on aircraft tires and struts having pneumatic pressure requirements up to 600 psi. It includes pressure relief provisions to provide for safe inflation. Also included are dual chuck stem gages for measuring tire pressure.
This specification covers a silicone resin in the form of a two-component liquid.
When identifying the content of this report, one of the goals was that it supports a nationally interoperable method for connected vehicles (CVs) to make traffic signal priority and/or preemption (TSPP) requests of connected intersections (CIs) that support priority and/or preemption services. Given that, this report specifies the over-the-air (OTA) interface between CVs and CIs to support TSPP applications using updated revisions of the SAE J2735 Signal Request Message (SRM) and Signal Status Message (SSM) and the use of a Wireless Access in Vehicular Environments (WAVE) Service Advertisement (WSA) to advertise support for TSPP at a CI. Included are a concept of operations, requirements, design, and message structure definitions developed using a detailed systems engineering process.
This specification covers a corrosion and heat resistant work strengthened nickel alloy in the form of bars and wire, 1½ inches (38 mm) and under in nominal diameter (See 8.2).
The present SAE Aerospace Information Report (AIR) provides a list of the main government regulations, SAE and international standards, and standing industry recommendations applying to air cargo unit load devices (pallets, nets, and containers) to be loaded with either baggage or freight on board civil transport aircraft.
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications.
This SAE Aerospace Recommended Practice (ARP) establishes the overall component and system function guidelines and minimum performance levels for a TPMS. These guidelines include, but are not limited to: Design recommendations for system components, which: Monitor tire inflation Are located in/on the tire/wheel assembly, landing gear axle, and/or aircraft avionics compartment Recommended performance and safety guidelines for a TPMS.
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
This SAE Recommended Practice establishes the antilock brake system (ABS) sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on or integral to the inboard end of spoke wheels, hubs, rotors, and hub-rotor assemblies on the following axle designations as defined in SAE J1842. a FF b FL c FC d FH e L f R g U h W j N k P
This specification establishes general requirements for the processes listed in 3.8.1 for heat treatment of steel parts (see 8.2.1) by users or their vendors or subcontractors.
This SAE Recommended Practice provides a uniform procedure and performance requirements for evaluating fastening systems for normal highway use on aftermarket passenger cars and light trucks (except dual wheels, which are covered by SAE J1965) and multipurpose passenger vehicles. The fastening system includes the wheel, wheel bolts, and wheel nuts, as well as vehicle mating surface. The coefficients of friction for steel and aluminum mating surfaces are provided based on information available. Many factors must be considered in design and validation of wheel attachments for each specific vehicle. Where the procedure is used for original equipment applications the vehicle manufacturers specifications supersede those noted.
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Items per page:
50
1 – 50 of 221567