Results
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
This specification covers the installation of aircraft interior lighting for military aircraft.
This specification defines limits of variation for determining acceptability of composition of cast and wrought corrosion and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy parts and materials acquired from a producer.
This test plan consists of two major sections for testing of MIL-STD-1553B data bus systems: Bus Network and System Integration Tests.
This SAE Aerospace Standard (AS) establishes the geometric control requirements for bolts, screws, and studs where worded notes and symbolized notes are used for straightness, concentricity, squareness, and runout.
This document recommends criteria to assure adequate visibility from the flight deck. The flight-deck windshield must provide sufficient external vision to permit the pilot to perform any maneuvers within the operating limits of the aircraft safely and, at the same time, afford an unobstructed internal view of the flight instruments and other critical components and displays from the same eye position.
The pressurization system design considerations presented in this AIR deal with human physiological requirements, characteristics of pressurization air sources, methods of controlling cabin pressure, cabin leakage control, leakage calculation methods, and methods of emergency cabin pressure release.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This specification covers the requirements for electrodeposed lead on metal parts.
This specification covers an aluminum alloy in the form of sheet laminated with one or more layers of unidirectional aramid fiber/epoxy prepreg.
This specification covers a nitriding grade of aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6497 and AMS6498 cover UNS K23280 having other quality levels.
This SAE Aerospace Recommended Practice (ARP) defines the test set-up requirements, general analysis procedures, and test report documentation for impact tests where photometric analysis of the high speed film or digital video will be required to obtain target paths (typically the Anthropomorphic Test Dummy (ATD) head path and knee path). Such tests support the requirements of AS8049 - Performance Standard for Seats in Civil Rotorcraft, Transport Aircraft and General Aviation Aircraft. These setup and analysis procedures are applicable to conventional, geometry based, two-dimensional analysis. If a more sophisticated technique that allows cameras to be installed at oblique angles for two or three-dimensional analysis is used, then the specific procedures required by that technique supersede any conflicting procedures contained herein. Some of the requirements that could be superseded include camera placement, optical data channel evaluation, camera to subject measurements, and scaling
This specification covers the requirements for electrodeposited tin-zinc alloy plating.
The purpose of this SAE Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, which is described by the diagnostic messages specified in SAE J1939-73, that is in accordance with off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off-board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy-duty engines used in medium- and heavy-duty vehicles. The development of HD OBD regulations by U.S. EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on
Items per page:
50
1 – 50 of 222094