Results
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This SAE Recommended Practice provides laboratory test procedures for testing headlamp aim test machines to verify their ability to aim or to inspect the aim of headlamps, fog lamps, and auxiliary high beam lamps. This specification does not apply to aiming devices of the kind covered by SAE J602. This specification does not apply to motorcycle headlamps.
The Mounting Height Task Force was tasked to determine the extent of the problem(s) associated with vehicle headlamps mounted at or above the level of the mirror(s) in passenger vehicles; the level of glare exposure caused by high-mounted headlamps; the appropriate height differential needed to maintain a glare level consistent with past and/or current passenger vehicle headlamp mounting; and the necessary headlamp mounting height necessary to control mirror glare at an accepted/acceptable level. The report herein addresses these passenger vehicle mounting height issues.
This SAE Standard measures the percent thermal efficiency of materials in sleeve form used to contain heat or insulate around a hot component. The percent thermal efficiency (%TE) is determined by measuring the power difference expended by the heat source (cartridge heater) with and without the test sleeve at the specified temperature. See SAE J2302 to measure radiant heat flow of sleeves.
This SAE Recommended Practice covers the number, location, and method of attachment of safety chains for full trailers and/or converter dollies.
Scope is unavailable.
The intended upper bound of this specification is that the particle size distribution (PSD) of powders supplied shall be <60 mesh (250 μm) and that no powder (0.0 wt%) greater than 40 mesh (425 μm) is allowed.
This specification covers the specific requirements for 2024 aluminum alloy plate and sheet; the general requirements are covered in AMS-QQ-A-250.
This specification covers an aluminum alloy in the form of high-strength sand, permanent mold, and composite mold castings of four classes.
Gas, for the purpose of this ARP, shall be defined as the gaseous product(s) resulting from the decomposition, dissociation, or combustion of liquid or solid mono or bi-propellants. Where other gases such as heated N2, H2, H2O (steam), etc., which may have similar physical and/or chemical properties as the defined "gas", are used to effect testing economics, they may he considered as being included in this ARP.
This document presents criteria for design and location of passenger reading lights in commercial aircraft. For LED reading light requirements, see ARP5873, titled: LED Passenger Reading Light Assembly.
This specification covers one type of sintered metal powder in the form of oil-impregnated bearings.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing produced with cross-sectional area of 32 square inches (206 cm2), maximum (see 8.6).
This specification covers an aluminum alloy in the form of sheet.
This specification covers a perfluoroether elastomer in the form of molded rings.
This specification covers an aluminum alloy in the form of pre-alloyed powder.
This specification covers a corrosion-resistant steel in the form of plate up to 3.00 inches (76.2 mm), inclusive, in nominal thickness.
This specification covers polyurethane systems consisting of an isocyanate component and other components containing a polyol and other ingredients which, when mixed and cured, produce thermosetting, rigid, cellular products.
This specification covers ground type hydropneumatic pressure accumulators for use in ground support hydraulic systems at rated pressures ranging up to 5,000 psi including details pertinent to the design, fabrication, and performance of the accumulators.
This SAE Aerospace Standard (AS) defines the requirements for a lightweight polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high temperature, 400 °F, high pressure, 3000 psi, aircraft hydraulic systems, also for use in pneumatic systems which allow some gaseous diffusion through the PTFE wall.
This document defines a set of standard application layer interfaces called JAUS Manipulator Services. JAUS Services provide the means for software entities in an unmanned system or system of unmanned systems to communicate and coordinate their activities. The Manipulator Services represent platform-independent capabilities commonly found across domains and types of unmanned systems. At present, twenty-five (25) services are defined in this document. These services are categorized as: Low Level Manipulator Control Services – The one service in this category allows for low-level command of the manipulator joint actuation efforts. This is an open-loop command that could be used in a simple tele-operation scenario. The service in this category is listed as follows: Primitive Manipulator Service Manipulator Sensor Services – These services, when queried, return instantaneous sensor data. Three services are defined that return respectively joint positions, joint velocities, and joint
This document defines performance standards which fiber optic cable splices must meet to be accepted for use in aerospace platforms and environments.
This specification covers a single-component, heat-reactive, thermosetting aromatic system which thermally cures to form a polyimide polymer structure.
This specification covers a titanium alloy in the form of pre-alloyed powder.
This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 °F. Gaseous service shall be limited to 150 °F.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This Aerospace Standard (AS) covers the general minimum performance standards for generators/starter-generators and associated voltage regulators for use in direct current (DC) electric systems for civil aircraft.
Items per page:
50
1 – 50 of 219717