Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process. This Recommended Practice is applicable during product and process development, product verification and quality control. This Recommended Practice does not replicate or predict actual vehicle performance or part durability.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers a copper-zinc alloy (brass) in the form of laminated sheet with nominal thickness 0.006 to 0.125 inch (0.15 to 3.18 mm) (see 8.5).
This SAE Standard defines methods and apparatus to evaluate electronic devices for immunity to potential interference from conducted transients along battery feed or switched ignition inputs. Test apparatus specifications outlined in this procedure were developed for components installed in vehicles with 12-V systems (passenger cars and light trucks, 12-V heavy-duty trucks, and vehicles with 24-V systems). Presently, it is not intended for use on other input/output (I/O) lines of the device under test (DUT).
This SAE Standard for reliability-centered maintenance (RCM) is intended for use by any organization that has or makes use of physical assets or systems that it wishes to manage responsibly.
This specification covers one weight and one weave of nylon cloth.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% polyimide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification establishes maximum permissible limits for elements not normally specified but which may occur in trace amounts in wrought nickel, cobalt, and iron alloy products.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products.
This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products.
This specification covers a lead alloy in the form of sheet and extrusions.
This SAE Standard identifies contractor activities for planning and conducting HSI as part of procurement activities on Department of Defense (DoD) system acquisition programs. This standard covers HSI processes throughout system design, development, test, production, use, and disposal. Depending on contract phase, type of the program and/or complexity of the program, tailoring of this standard should be applied. Appendix A lists the requrememts (“shall” statements) in this standard along with unique numbers to facilitate tailoring. In addition, Appendix D provides tailoring guidance to better match requirememts in this standard to the DoD’s Adaptive Acquisition Framework pathways. The scope of this standard includes prime and subcontractor HSI activities; it does not include Government HSI activities, which are covered by DoD and service-level regulations and guidelines. HSI programs should use the latest version of standards and handbooks listed below, unless a particular revision is
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers a standard fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.
This specification covers a petroleum-base solvent in the form of a liquid.
This specification covers established inch/pound manufacturing tolerances applicable to copper and copper alloy wire ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted.
In 1941, the SAE Iron and Steel Division in collaboration with the American Iron and Steel Institute (AISI) made a major change in the method of expressing composition ranges for the SAE steels. The plan, as now applied, is based in general on narrower ladle analysis ranges plus certain product (check) analysis allowances on individual samples, in place of the fixed ranges and limits without tolerances formerly provided for carbon and other elements in SAE steels (reference SAE J408). ISTC Division 1 has developed a procedure which allows for the maintenance of the grade list in this SAE Standard. This will involve conducting an industry-wide survey to solicit input. This survey will be conducted at a frequency deemed necessary by the technical committee. Criteria have been established for the addition to or deletion of grades from the grade table. A new grade will be considered if it meets standard SAE grade ranges, has a minimum usage or production of 225 tonnes/year (250 tons/year
This specification covers one type of organic (para-aramid) fiber in the form of roving. The product shall be formed as a number of ends, tows, or strands collected into a parallel bundle with little or no twist.
This specification covers one weight and strength of para-aramid thread.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm) inclusive, in nominal diameter, and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm) inclusive, in nominal thickness (see 8.5).
This specification covers one type of parchment in the form of rolls of sheeting or reels of unperforated tape of the width specified.
This specification covers one class of para-aramid tape and webbing of a single width and with varying weights.
This specification covers one type of epoxy-resin-impregnated boron filaments 0.0040 inch (0.102 mm) in diameter in the form of continuous tape supported on a glass cloth carrier.
This specification covers an aluminum-killed carbon steel in the form of sheet and strip.
This specification covers a cobalt alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 60% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
This specification covers one type of organic (para-aramid) fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers one type of nylon in the form of webbing.
This specification establishes the requirements for a general-purpose brush plating of nickel applied by electrodeposition.
This specification covers a fluorocarbon (FKM) rubber stock in the form of molded test slabs.
Items per page:
50
1 – 50 of 216101