Results
This SAE Recommended Practice provides a common method to measure wear of friction materials (brake pad assemblies and brake shoes) and their mating parts (brake disc or brake drum). These wear measurements apply to brakes fitted on passenger cars and light trucks up to 4536 kg of Gross Vehicle Weight Rating under the Federal Motor Vehicle Safety Standard (FMVSS), or vehicles category M1 (passenger cars up to nine occupants, including the driver) under the European Community’s ECE Regulations.
This SAE Aerospace Standard (AS) covers miniature, composite, high density, threaded coupling, self-locking, circular, environment-resistant, electrical connectors utilizing removable crimp contacts, and associated hardware, which are capable of continuous operation within a temperature range of -65 to +175 °C (-85 to 347 °F). These connectors are supplied under an AS9100 reliability assurance program. See 6.1 for intended use and applications.
SCOPE IS UNAVAILABLE.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in nominal thickness at the time of heat treatment and having an OD to wall thickness ratio of 10 or greater (see 8.6).
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Aerospace Standard (AS) defines the requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in 400 °F, 3000 psi aircraft hydraulic systems. Assemblies are suitable where rapid rate pressure pulsing and torsional/ longitudinal flexing may occur, in addition to normal hydraulic system loads.
This SAE Aerospace Recommended Practice (ARP) establishes the factors which should be considered in the design and installation of a commercial transport rotorcraft hydraulic system, including the applicable airworthiness regulations that affect the hydraulic system. This ARP also provides information and guidelines on the many factors that arise in the design process to provide cost effectiveness, reliability, maintainability and accepted design and installation practices.
This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 °F. Gaseous service shall be limited to 150 °F.
This SAE Aerospace Standard (AS) defines the requirements for a lightweight polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high temperature, 400 °F, high pressure, 3000 psi, aircraft hydraulic systems, also for use in pneumatic systems which allow some gaseous diffusion through the PTFE wall.
This SAE Aerospace Information Report (AIR) provides design data reliability information relative to the long-term storage of gas containers or pressure vessels charged with nitrogen or helium at pressures ranging from 6000 to 12 000 psi. The gas containers are cylindrical, spherical, or toroidal in shape. Internal volumes range up to 1385 in3. Applications for this type cold gas actuation system include tactical missiles, guided projectiles, and smart bombs. A typical system is described.
Although there is controversy regarding the chemical form of chlorine and its relation to harmful effects in the hydraulic fluid (i.e., chloride ions versus organic chloro-compounds versus total chlorine in all forms), it is generally agreed that total chlorine content should be measured and controlled. In the near future, the ban on the manufacture of chlorinated solvents, out of concern for depletion of the ozone layer, may in itself diminish or eliminate chlorine contamination related aircraft malfunctions. It is generally accepted that hydraulic fluid contamination should be held to a minimum under all conditions. The benefits of low contamination levels are improved performance, lower maintenance due to lower wear, corrosion and erosion, longer fluid life, longer component life, etc. Contaminants can be classified into two general types: those that are insoluble and those that are soluble in the hydraulic fluid. The insoluble solid type is most common and is usually referred to as
This SAE Standard provides test procedures, performance requirements, and guidelines for semiautomatic headlamp beam switching (SHBSD) devices.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes additional performance requirements and provides test methods and requirements to evaluate the suitability of materials intended for optical applications in motor vehicles. The tests are intended to determine physical and optical characteristics of the materials only. Performance expectations of finished assemblies, including plastic components, are to be based on tests for lighting devices, as specified in SAE Standards and Recommended Practices for motor vehicle lighting equipment. Glass and materials inclusive to the light source are not in scope for this method.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up trucks with dual wheels, and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal to the driver of following (approaching a signaling vehicle from the rear) or oncoming (approaching a signaling vehicle from the front) vehicles over intervening vehicles.
This specification covers an aluminum alloy in the form of die forgings from over 2.000 to 10.000 inches (50.8 to 254 mm) in nominal thickness and forging stock of any size (see 8.6).
This SAE Recommended Practice describes the testing procedures that may be used to evaluate the integrity of ground ambulance-based occupant seating and occupant restraint systems for workers and civilians transported in the patient compartment of an ambulance when exposed to a frontal or side impact. This recommended practice was based on ambulance patient compartment dynamics and is not applicable to other vehicle applications or seating positions. This recommended practice is structured to accommodate seating systems installed in multiple attitudes including, but not limited to, side-facing, rear-facing, and forward-facing. Its purpose is to provide ambulance seating manufacturers, ambulance occupant restraint manufacturers, ambulance builders, and end users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensures the occupant seating and occupant restraint system meet similar performance criteria as FMVSS 208 requires for seat belted
This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: Tracking transmitter Tracking receiver Telemetry device Remote display This type of tracking equipment is typically used with horizontal earthboring machines as defined in SAE J2022.
An attempt has been made to consider all features of seal ring design including configuration, materials, hardness, dimensions, surface finishes, surface treatment, leak testing, and general quality. In addition to this, allowable cylinder breathing and general quality requirements of mating hardware are discussed. Also, at the end of this report, there is a brief paragraph on other types of seal rings.
This SAE lab recommended practice may be applied to corrosion test methods such as salt spray, filiform, Corrosion creep back, etc. This procedure is intended to permit corrosion testing to be assessed between Laboratories for correlation purposes.
This Aerospace Standard (AS) provides the general requirements for hydraulic components that are used in military aircraft and missile hydraulic systems.
This SAE Aerospace Recommended Practice (ARP) establishes software capability guidelines for computer controlled test equipment, hereinafter referred to as automatic test equipment (ATE), for testing hydraulic components. A typical ATE system is shown in Figure 1. The items herein have been selected as potential features which may or may not be applicable to a particular application. This document does not address software development requirements, qualification procedures, or hardware design requirements, but encourages users to refer to existing documents, defined in 2.1.1, for guidance on such issues.
This specification covers the design requirements and test procedures for separable beam seal fittings which includes end fittings (see 2.3.4), fitting bodies (see 2.3.7), and boss fittings (see 2.3.2) for use in aerospace fluid systems. Design requirements are for class 3000 in corrosion resistant steel (15-5 PH, 17-4 PH CRES) only and for class 4000 in titanium alloy (Ti) and corrosion and heat-resistant steel (nickel alloy 718 CRES) only. Definition of fittings and related terms are defined in 2.3.
Various gas systems are classified in a broad sense, component operation is described in moderate detail, pertinent design parameters are discussed, and possible modes for system operation are listed.
These recommendations cover the mechanical and electrical installation and installation test procedures for automatic pilots of the type normally used in transport type aircraft. The material in this ARP does not supercede any airworthiness requirement in the Civil Air Regulations.
This SAE Aerospace Recommended Practice (ARP) applies to airline trailer equipment with four wheel running gear pulled and steered through an integral tow bar, for use on airport ramps and other airport areas for transporting baggage, freight, and other materials. This ARP can apply to any airline/airport trailer chassis regardless of its equipment; the trailer bed can be designed to carry either bulk baggage/cargo, or a cargo unit load device by means of a rollerized conveyor system, or a piece of aircraft servicing equipment (e.g., ground power unit, air start unit, etc.).
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
Gas, for the purpose of this ARP, shall be defined as the gaseous product(s) resulting from the decomposition, dissociation, or combustion of liquid or solid mono or bi-propellants. Where other gases such as heated N2, H2, H2O (steam), etc., which may have similar physical and/or chemical properties as the defined "gas", are used to effect testing economics, they may he considered as being included in this ARP.
This SAE Aerospace Recommended Practice (ARP) covers the design and installation requirements for hydraulic systems (up to 8000 psig [56 MPa]) for ground support equipment (GSE). This ARP is derived from AS5440, which provides hydraulic system requirements for aircraft. The recommendations herein are primarily intended for GSE that exchange hydraulic fluid with the aircraft, such as hydraulic service carts, rather than GSE with non-interfacing hydraulic systems. The GSE may be mobile, portable, or stationary.
Items per page:
50
1 – 50 of 215781