Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
SAE J1939-75 defines the set of data parameters (SPs) and messages (PGs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPs) and messages (PGs) previously published within this document are published in SAE J1939DA. Applications using the SAE J1939-75 document must refer to SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD with nominal wall thickness 0.015 inch (0.38 mm) and over.
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This SAE Information Report establishes the Use Cases for communications and customer-focused Key Performance Indicators (KPI) between plug-in electric vehicles (PEVs) and their customers. The Use Case Scenarios define the information to be communicated related to customer convenience features for charge on/off control, charge power curtailment, customer preference settings, charging status, electric vehicle supply equipment (EVSE) availability/access, and electricity usage, plus customer information resulting from conflicts to charging preferences. It also addresses the KPI that can provide a uniform set of metrics to quantitively assess the charging experience. This document only provides the Use Cases that define the communications requirements to enable customers to interact with the PEV and the KPI to optimize their experience with charging a PEV. Specifications such as protocols and physical transfer methods for communicating information are not within the scope of this document.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This specification covers an aluminum alloy in the form of clad sheet 0.006 to 0.249 inch (0.015 to 6.32 mm), inclusive, in thickness (see 8.6).
This SAE Aerospace Standard (AS) defines the requirements for a polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high pressure, 4000 psi, pneumatic systems for aircraft and missile ground servicing applications at temperatures of -65 to 160 °F.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of rods, sheets, and molded shapes.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of sheet 0.250 inch (6.35 mm) and over in thickness, rod, heavy wall tubing, and large molded and machined parts.
This report revises ARD50015 document to the AIR format. This report, as was the original, is intended to complement ARP1420C and AIR1419C documents issued by the SAE S-16 Committee on spatial total-pressure distortion. These previous documents addressed only total-pressure distortion and excluded total temperature distortion. The subject of inlet total temperature distortion is addressed in this report with some background and identification of the problem area. The status of past efforts is reviewed, and an attempt is made to define where we are today. Deficiencies, voids, and limitations in knowledge and test techniques for total temperature distortion are identified.
This test method outlines the recommended procedure for performing static radial limit and ultimate load tests on rolling element bearings used in airframe applications. Bearings covered by this document shall be antifriction ball bearings and spherical roller bearings in either annular or rod end configurations.
This document is offered to provide state-of-the-art information about design factors that must be considered in the design of new or significantly modified engine test cells used to test propeller equipped turboprop engines in either QEC or bare engine configurations. The report does not address design considerations for test cells designed to test turboprop engines with dynamometer type load absorption devices because they are essentially tested as turboshaft engines. Design considerations for those test cells are presented in AIR4989, Reference 2.1.
This specification covers one weight and one weave of nylon cloth.
This specification covers the specific requirements for aluminum alloy 7075 bar, rod, shapes, tube, and wire produced by extrusion.
This specification covers an aluminum alloy in the form of extruded rods, bars, and profiles (shapes) produced with thicknesses 0.040 to 2.500 inches (1.02 to 38.10 mm), inclusive, having a maximum cross-sectional area of 23 square inches (15000 mm2) and a maximum circumscribing circle diameter (circle size) of 16 inches (406 mm) (see 2.4.1 and 8.7).
This test method outlines a standard procedure for performing cyclic reversing load testing on oscillating sliding bearings. The wear data from these tests is to be used for qualification requirements and to establish bearing design criteria.
This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet.
Items per page:
50
1 – 50 of 215949