Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This document is intended for use by manufacturers of aircraft, engines and Electronic Engine Controls [EECs] as a component change process and evaluation guideline. Its purpose is to provide an effective means of managing the modification of electronic hardware. The process defined in this document is based upon: an understanding of the electronic component market evolution, e.g., obsolescence; lessons learned from the effects caused by the introduction of electrical component changes in a service fleet environment; industry best practice; and an understanding of the applicable regulations.
This SAE Aerospace Information Report (AIR) has been written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in upgrading their existing or acquiring new test cell facilities.
This specification covers silicone (VMQ) rubber sheet reinforced with glass cloth.
This specification covers the requirements for filled, resinous thermosetting compound and sheet pre-preg to fabricate shims for use during assembly of aircraft and marine components and parts.
This specification covers a corrosion and heat-resistant nickel alloy in the form of investment castings.
This specification covers the general requirements for aluminum and aluminum alloy bar, rod, wire, or special shapes; rolled, drawn, or cold finished. Specific requirements for these products are covered by the applicable detail specification (See 6.3).
This specification covers the requirements for three types and three classes of mechanically deposited cadmium, tin-cadmium or zinc coatings on metallic surfaces by impacting (peen plating).
This specification covers a premium aircraft-quality alloy steel in the form of bars and forgings 199 square inches (1284 cm2) and under in cross section, and forging stock of any size.
This specification covers the requirements for electrodeposited tin-lead plating intended for use as a coating for corrosion protection and as a base for soldering.
The requirements established in this document are applicable to the IAQG and associated sectors for managing oversight to established requirements contained in 9104-series standards (i.e., 9104/1, 9104/2, 9104/3). The requirements are applicable to IAQG working groups for oversight. NOTE: All required forms are depicted in Appendix A. These form exhibits are provided for reference only; the current versions of these forms are available on the IAQG website.
This specification covers types and classes of polysulfide sealing compound supplied as a two-component system suitable for application by brush, or by extrusion gun, spatula brush, or roller.
This specification covers the requirements of composite blankets suitable for acoustical and thermal insulation of the walls of aircraft compartments within the temperature range of -65°F to +175°F (-54°C to +80°C).
This specification presents requirements for the carburizing and nitriding of carbon and alloy steels to produce the mechanical properties specified by drawings, detail metal specifications, or other applicable specifications (see 6.3).
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a titanium alloy in the form of investment castings.
This standard establishes the acceptance criteria for surface discontinuities as revealed by magnetic particle or liquid penetrant examination of nuts.
This document covers all metal, castellated, self-locking nuts made from alloy steel of the types identified under the Unified Numbering System as UNS G41300 and UNS G43400.
This AIR is limited to the requirements of AS50881 and examines these requirements, providing rationale behind them. AS50881 is only applicable to the aircraft EWIS. Pods and other devices that can be attached to an aircraft are considered as part of the aircraft equipment design. Its scope does not include wiring inside of airborne electronic equipment but does apply to wiring externally attached to such equipment. The AS50881 scope does not include attached devices but does include the interface between the pod/equipment and aircraft wiring. Section 3.3.5 addresses components such as antennas and other similar equipment that were once supplied as Government Furnished Aeronautical/Aerospace Equipment (GFAE).
Items per page:
50
1 – 50 of 221567