Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies, including the following spectrum: a. At one end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. b. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This SAE Recommended Practice provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies.
This SAE Recommended Practice provides test protocols with performance requirements for camera monitor systems (CMS) to replace existing statutorily required inside and outside rearview mirrors for U.S. market road vehicles. This practice expands specific technical content while retaining harmonization with the FMVSS 111 rear visibility standard and other international standards. This is accomplished by defining required roadway fields of view as specific fields of view (FOV) displayed inside the vehicle. Specific testing protocols and/or specifications are added to enhance ease of use using straightforward language, and any specifications are intended to be independent of different camera and display technologies unless otherwise explicitly stated.
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
Three levels of fan structural analysis are included in this practice: a Initial structural integrity. b In-vehicle testing. c Durability (laboratory) test methods. The initial structural integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The in-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The durability test methods section describes the detailed test procedures for a laboratory environment that may be used depending on type of fan, equipment availability, and end objective. The second and third levels build upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a
This specification covers a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
The scope of this SAE Recommended Practice is to promote compatibility between child restraint systems and vehicle seats and seat belts. Design guidelines are provided to vehicle manufacturers for certain characteristics of seats and seat belts and to child restraint system (CRS) manufacturers for corresponding CRS features so that each can be made more compatible with the other. The CRS accommodation fixture (see Figure 1) is used to represent a CRS to the designers of both the vehicle interior and the CRS for evaluation of each product for compatibility with the other. The features of the accommodation fixture are described as each is used.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
Applies to hydraulic fluid power valves as applied to Off-Road Self-Propelled Work Machines defined in SAE J1116.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice establishes uniform procedures for testing BEVs that are capable of being operated on public and private roads. The procedure applies only to vehicles using batteries as their sole source of power. It is the intent of this document to provide standard tests that will allow for the determination of energy consumption and range for light-duty vehicles (LDVs) based on the federal test procedure (FTP) using the urban dynamometer driving cycle (UDDS) and the highway fuel economy driving schedule (HFEDS) and provide a flexible testing methodology that is capable of accommodating additional test cycles as needed. Additionally, this SAE Recommended Practice provides five-cycle testing guidelines for vehicles performing supplementary testing on the US06, SC03, and cold FTP procedures. Realistic alternatives should be allowed for new technology. Evaluations are based on the total vehicle system’s performance and not on subsystems apart from the vehicle.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel in the form of investment castings, solution and precipitation heat treated to 180 ksi (1241 MPa) tensile strength.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6497 cover UNS K23280 with other quality levels.
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a corrosion and heat resistant steel in the form of sheet, strip, and plate.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in thickness (see 3.3.1.1.1) and an OD to wall thickness ratio of 10 or greater (see 8.5).
This SAE Aerospace Standard provides minimum design, installation, and removal requirements for AS3319 through AS3322 studs and is applicable when specified on engineering drawings, or in procurement documents.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
Items per page:
50
1 – 50 of 216106