Results
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This specification covers three classes of fuel-resistant polysulfide (T) sealing compound with high strength and temperature characteristics, supplied as a two-component system which cures at room temperatures.
This SAE Aerospace Standard (AS) establishes the requirements for 24 degree cone AS5827 or EN 6123 flareless ring locked fitting assemblies per AS5550 and AS5865, for use in aircraft fluid systems at nominal operating pressure of 5080 psi (35000 kPa) maximum and operating temperature range of -65 to +275 °F (-54 to +135 °C). The general requirements shall be for, but not limited to, commercial aircraft hydraulic components per AS4941, using port configuration as specified in AS5551.
This SAE Aerospace Recommended Practice (ARP) covers the design and installation requirements for hydraulic systems (up to 8000 psig [56 MPa]) for ground support equipment (GSE). This ARP is derived from AS5440, which provides hydraulic system requirements for aircraft. The recommendations herein are primarily intended for GSE that exchange hydraulic fluid with the aircraft, such as hydraulic service carts, rather than GSE with non-interfacing hydraulic systems. The GSE may be mobile, portable, or stationary.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification and defines how to implement transmission control protocol (TCP) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/18_0500 interface shall be compliant to the TCP CLIENT feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/13_0500 (ethernet), SAE J2534-2/16_0500 (IPv4), SAE J2534-2/15_0500 (IPv6), SAE J2534-2/BA_0500, and SAE J2534-2/RE_0500 documents.
This SAE Aerospace Information Report (AIR) provides an orientation regarding the general technology of chemical oxygen generators to aircraft engineers for assistance in determining whether chemical oxygen generators are an appropriate oxygen supply source for hypoxia protection in a given application and as an aid in specifying such generators. Information regarding the details of design and manufacture of chemical oxygen generators is generally beyond the scope of this document.
In this report, "Cryogenically Fueled Dynamic Power Systems" include all open cycle, chemically fueled, dynamic engine power systems which utilize cryogenic fuels and oxidizers. For nearly all practical present day systems, this category is limited to cryogenic hydrogen or hydrogen-oxygen fueled cycles with potential in future, more advanced systems for replacement of oxygen by fluorine. Excluded from the category are static cryogenic systems (e.g., fuel cells) and chemical dynamic power systems which utilize earth storable propellants.
The purpose of this document is to establish air-conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system; since these characteristics and conditions vary greatly from one application to another, the designer shall determine the goals expected to be reached under the conditions encountered. To determine the capacity of such items as blowers, condenser fans, condenser coils, evaporator coils, filters, compressors, etc., will require the adherence to several guidelines, some of which are outlined in the following paragraphs.
This standard requires the developers and customer/users working as a team to plan and implement a reliability program that provides systems/products that satisfy the user’s requirements and expectations. The user’s requirements and needs are expressed in the form of the following four reliability objectives: The developer shall solicit, investigate, analyze, understand and agree to the user’s requirements and product needs. The developer, working with the customer and user, shall include the activities necessary to ensure that the user’s requirements and product needs are fully understood and defined, so that a comprehensive design specification and Reliability Program Plan can be generated. The developer shall use well-defined reliability- and systems-engineering processes to develop, design, and verify that the system/product meets the user’s documented reliability requirements and needs. The developer shall implement a set of engineering activities (included in this standard as
This standard specifies the areas to be used in calculating stress or load values to be used in externally and internally threaded fastener procurement specifications for bolts, screws, nuts, and studs and for the information of designers.
This SAE Aerospace Standard (AS) defines the requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in 400 °F, 3000 psi aircraft hydraulic systems. Assemblies are suitable where rapid rate pressure pulsing and torsional/ longitudinal flexing may occur, in addition to normal hydraulic system loads.
This Aerospace Information Report (AIR) has been written to provide in-service reliability data of continuously active ball screw and geared flight control actuation systems.
This SAE Aerospace Standard (AS) covers 6-point and 12-point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box end and flare nut wrenches, combination open end and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) non-distorting usage; (b) possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 and ISO 8434-2; and (c) transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Various gas systems are classified in a broad sense, component operation is described in moderate detail, pertinent design parameters are discussed, and possible modes for system operation are listed.
This standard defines the common nonconformity data definition and documentation that shall be exchanged between an internal/external supplier or sub-tier supplier, and the customer when informing about a nonconformity requiring formal decision. The requirements are applicable, partly or totally, when reporting a product nonconformity to the owner or operator, as user of the end item (e.g., engine, aircraft, spacecraft, helicopter), if specified by contract. Reporting of nonconformity data, either electronically or conventionally on paper, is subject to the terms and conditions of the contract. This also includes, where applicable, data access under export control regulations.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers a corrosion-resistant steel in the form of plate up to 3.00 inches (76.2 mm), inclusive, in nominal thickness.
This SAE Aerospace Standard defines a typical coupling (with different fitting end styles), which is used in typical cone connection fittings installed in high-pressure (up to 3000 psi) oxygen systems for the purpose of mating to applicable oxygen equipment. Dimensions are developed from AND10089 and AS4375.
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR.
This SAE practice is intended for the sample preparation of test pieces for automotive wheels and wheel trim. The practice provides a consistent scribing method for use on test panels and or component parts with substrate chemical pretreatment and coating systems. Test specimens can then be subjected to various corrosion tests in order to evaluate performance without significant variations of the degree of exposure of the substrate. The scribing is used to create a break in the coating/finishing as can occur in the field through gravel and other damaging conditions. NOTE— Significant variability is attributed to surface contour, coating hardness/softness, operator reproducibility, and the scribing tool and it’s condition.
The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive references.
This test method is applicable for rating various materials, such as automotive trim materials and insulation composites, for their ability to resist heat transfer, heat degradation, odor, smoking, and exothermic reaction under prescribed temperature.
Items per page:
50
1 – 50 of 220494