Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
SAE J1939-75 defines the set of data parameters (SPs) and messages (PGs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPs) and messages (PGs) previously published within this document are published in SAE J1939DA. Applications using the SAE J1939-75 document must refer to SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
This specification covers a titanium alloy in the form of bars 6.000 inches (152.40 mm) and under in nominal diameter or least distance between parallel sides, forgings, flash-welded rings 6.000 inches (152.40 mm) and under in thickness, and stock for forging and stock for flash-welded rings of any size (see 8.6).
This SAE Information Report establishes the Use Cases for communications and customer-focused Key Performance Indicators (KPI) between plug-in electric vehicles (PEVs) and their customers. The Use Case Scenarios define the information to be communicated related to customer convenience features for charge on/off control, charge power curtailment, customer preference settings, charging status, electric vehicle supply equipment (EVSE) availability/access, and electricity usage, plus customer information resulting from conflicts to charging preferences. It also addresses the KPI that can provide a uniform set of metrics to quantitively assess the charging experience. This document only provides the Use Cases that define the communications requirements to enable customers to interact with the PEV and the KPI to optimize their experience with charging a PEV. Specifications such as protocols and physical transfer methods for communicating information are not within the scope of this document.
This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings (see 8.6).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD with nominal wall thickness 0.015 inch (0.38 mm) and over.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
This SAE recommended practice defines and establishes tolerances and attributes of cold rolled strip steels. Differences between cold rolled strip and cold rolled sheet products are discussed so that process designers can make informed material selection decisions.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers an aluminum alloy in the form of hand forgings 12 inches (305 mm), inclusive, and under in nominal thickness and forging stock of any size (see 8.5).
This specification covers the requirements of uncoated aluminum alloy foil for core materials required for structural sandwich construction.
This specification establishes requirements for thermoset protective coatings in powder form.
This specification covers an aluminum alloy in the form of permanent mold castings (see 8.6).
This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles up to 0.499 inches (12.67 mm) in nominal diameter, or least thickness, and under 10 in2 (65 cm2) in cross-sectional area.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of welding rods or wrought wire.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars and forgings in the solutioned, stabilized, and precipitation heat-treated condition. Stock for forging shall be in the condition ordered.
This specification covers an aluminum alloy in the form of seamless drawn tubing having nominal wall thickness of 0.018 to 0.500 inch (0.46 to 12.70 mm), inclusive (see 8.4).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers an aluminum alloy in the form of plate 0.500 to 1.500 inches (12.70 to 38.10 mm), inclusive, in thickness (see 8.5).
The information and data contained in this SAE Information Report are intended as a guide in the selection of steel types and grades for various purposes. Consideration of the individual types of steel is preceded by a discussion of the factors affecting steel properties and characteristics. SAE steels are generally purchased on the basis of chemical composition requirements (SAE J403, J404, and J405). High-strength, low alloy (HSLA) steels (SAE J1392 and J1442) are generally purchased on the basis of mechanical properties; different chemical compositions are used to achieve the specified mechanical properties. Because these steels are characterized by their special mechanical properties obtained in the as-rolled condition, they are not intended for any heat treatment by the purchaser either before, during, or after fabrication. In many instances, as in the case of steels listed in SAE J1268 and J1868, hardenability is also a specification requirement. This information report can be
This SAE Recommended Practice covers a high-strength corrosion-resisting steel wire, uniform in mechanical properties, intended for the manufacture of springs and wire forms. It also covers processing requirements of springs and forms fabricated from this wire.
This specification covers a corrosion- and heat-resistant nickel-iron alloy in the form of bars and forgings 5 inches (127 mm) and under in nominal diameter or least distance between parallel sides and forging stock of any size.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification and its supplementary detail specifications cover a woven nylon cloth coated with polyether (EU) urethane.
This specification covers a polychloroprene-coated, one side only, nylon knit in the form of cloth.
This specification covers thoria-dispersion-strengthened nickel in the form of sheet and strip.
This specification covers a woven nylon cloth coated with polyether (EU) urethane.
This specification covers a filled, resinous, thermosetting, precatalyzed, liquid compound capable of being applied and cured in place between the surfaces of mechanically fastened (joined) structures.
Items per page:
50
1 – 50 of 215951