Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
Applies to hydraulic fluid power valves as applied to Off-Road Self-Propelled Work Machines defined in SAE J1116.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers an aluminum alloy in the form of sheet clad on both sides with a different aluminum alloy.
This specification covers an aluminum alloy powder metallurgy product in the form of sheet 0.010 to 0.250 inch (0.25 to 6.35 mm) in nominal thickness.
To define a list of anomalies related to OBD Communications. Misinterpretations of various OBD Communications Standards and Recommended Practices have resulted in OBD “no-communications” situations in the field. This Information Report identifies the most prevalent of these.
This SAE Information Report establishes a consistent procedure for measuring and analyzing the natural sway response of a particular trailer when attached to a particular vehicle under specific loading and operating conditions. This test procedure applies, but is not limited to, passenger cars, vans, light/medium-duty trucks as tow vehicles, and semitrailers with a Gross Vehicle Weight Rating (GVWR) of 11794 kg (26000 pounds) or less. Other applications include full trailers, tow dollies, tow bars, and the like. Other articulated vehicles can utilize this test procedure as long as the test does not exceed the linear behavior of the system. This test procedure does not apply to motorcycles towing trailers.
This document describes a physical layer utilizing Unshielded Twisted Pair (UTP) cable with extended stub lengths for flexibility in ECU placement and network topology. Also, connectors are not specified. CAN controllers used on SAE J1939-15 networks must be restricted to use only Classical Frames as defined in ISO 11898- 1. A network which may have legacy controllers cannot tolerate FD Frames. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
This method is intended to define the continuous upper temperature limit (CUTL) of thermoplastic elastomers and thermoset rubber with durometer hardness <=90 Shore A, to oxidation or other degradation when exposed solely to hot air for an extended period of time.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This standard is applicable to the marking of aerospace vehicle electrical wires and cables using ultraviolet (UV) lasers. This standard specifies the process requirements for the implementation of UV laser marking of aerospace electrical wire and cable and fiber-optic cable to achieve an acceptable quality mark using equipment designed for UV laser marking of identification codes on aerospace wire and cable. Wiring specified as UV laser markable subject to AS4373 and which has been marked in accordance with this standard will conform to the requirements of AS50881.
This SAE Information Report should be used as a supplement to SAE J1383 (Reference 2.1.1). It is intended to provide additional information which is important to the automotive designer and engineer in the process of designing, developing, and engineering the headlamps of motor vehicles which will take into account the effects of the aging process on the driver.
This SAE Surface Vehicle Information Report identifies and defines the assembly/disassembly and certification procedures relating to the use of the Hybrid III Large Male Test Dummy.
This specification establishes the common requirements for variable delivery electric motor driven, hydraulic pump units, suitable for use in aircraft hydraulic systems.
The recommended practice describes a design standard that defines the maximum recommended voltage drop of the starting motor main circuits, as well as control system circuits, for 12/24-V starter systems. The battery technologies used in developing this document include the flooded lead acid, gel cell, and AGM. Starting systems supported by NiCd, Lithium Ion, NiZn, etc., or Ultracaps are not included in this document. This document is not intended to be updated or modified to include starter motors rated at voltages above the nominal 24-V electrical system. The starter is basically an electrical-to-mechanical power converter. If you double the available battery power in, you double the peak mechanical power out and double the heat losses. This means that we have to pay special attention to how battery power changes when we change the battery voltage and the effects it may have in overpowering the cranking system. A new stand-alone document would need to be developed to address
This SAE Information Report provides information on certain fuels that are being used or have been suggested as alternatives to motor gasoline (SAE J312) or automotive diesel fuel (SAE J313) for use in spark-ignition or compression-ignition engines. Some of these fuels are derived from petroleum while others are from non petroleum sources.
SAE J1939-81 (“Network Management”) defines the processes and messages associated with managing the addresses of applications communicating on an SAE J1939 network. Network management is concerned with the management of addresses and the association of those addresses with an actual function and with the detection and reporting of network related errors. Due to the nature of management of addresses, network management also specifies address selection and address claiming processes, requirements for reaction to brief power outages, and minimum requirements for ECUs on the network.
The purpose of this SAE Standard is to provide equipment specifications for CFC-12 (R-12) recovery for return to a refrigerant reclamation facility that will process it to the appropriate ARI Standard (Air Conditioning and Refrigerant Institute) or allow for recycling of the recovered refrigerant in equipment that is certified to meet the requirements of SAE J1991. Under the existing rule, the U.S. EPA requires refrigerant removed from a mobile air-conditioning (A/C) system using recovery equipment certified to meet SAE J2209 can only be recycled using equipment meeting SAE J1991 that is owned by the same company or individual. It is not acceptable that the refrigerant removed from a mobile A/C system, with this equipment, be directly returned to a mobile A/C system. This information applies to equipment used to service automobiles, light trucks, and other vehicles with similar CFC-12 (R-12) systems.
This SAE Recommended Practice is intended to provide basic recommended practices for aid in the development and use of safe and efficient practices for all operations involving the production, handling, and dispensing of SAE J1703 motor vehicle brake fluids and SAE J1704 borate ester-based brake fluids.
This SAE Aerospace Standard (AS) provides for aircraft reciprocating engines formats for altitude graph sheets recommended for use when presenting engine performance data.
This SAE Aerospace Recommended Practice (ARP) provides engineering methods that can be applied to monitoring aircraft noise and operations in the vicinity of airports using either attended or unattended monitoring systems, as well as methods for validation of measurement results from permanent systems. Part 1 provides guidance on the components, installation and administration of permanent systems and guidance on analysis of data collected from temporary monitoring of aircraft noise. Part 2, this part, describes both system screening tests and detailed test methods for validating the data reported by permanently installed systems. This document is intended as a guide toward standard practice and is subject to change with experience and technical advances. Potential users include: airport proprietors, airport neighbors, federal, state and local government agencies, equipment vendors and other public bodies and officials. Potential applications include: Part 1 - development of a basis
This specification covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
Items per page:
50
1 – 50 of 221567