Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
SCOPE IS UNAVAILABLE.
AMS6885/1 gives information about the technical requirements and qualification procedure for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The repair system includes an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
AMS6885/2 gives specific information about the qualification program for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This test method outlines the standard procedure for measuring the radial and axial internal clearance of rolling element bearings used in airframe controls.
This document describes the major design drivers and considerations when designing a fuel system for a large commercial aircraft. While not intended as a design manual for individual system components, it does refer out to other SAE specifications where more detail on specific components and subsystems is given. It does include examples of a number of calculations associated with sizing of fuel systems, based on those given in NAVAIR 06-5-504, as well as an appendix summarizing basic fluid mechanical equations that are key for fuel system design. It is acknowledged that most of these calculations would today be performed by modeling tools rather than by hand, but it is considered important for the designer to understand the principles. Some details specific to military aircraft are included, but it is intended that later issues of this document will include appendices that give specific considerations for military aircraft, smaller commercial aircraft, and rotorcraft. Features unique
This specification covers the requirements for electrodeposited gold plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and foil 0.100 inch (2.54 mm) and under in nominal thickness.
This SAE Aerospace Recommended Practice (ARP) is intended to be used for laser systems mounted on aircraft and propagated into navigable airspace. This does not include lasers onboard aircraft where the beam is contained within an enclosure so that the beam cannot enter into airspace, nor does it include lasers from satellites and spacecraft in outer space. It may be used in conjunction with AS4970, ARP5535, ARP5572, ARP5293, and the ANSI Z136 laser safety standards.
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
SCOPE IS UNAVAILABLE.
This specification establishes the engineering requirements for the uphill quenching process of aluminum alloy product. Uphill quenching immerses product in liquid nitrogen followed by exposure to a high-pressure/high-velocity steam blast or boiling water.
This specification covers a copper alloy in the form of strip (see 8.6).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing produced with cross-sectional area of 32 square inches (206 cm2), maximum (see 8.6).
This specification covers beryllium in the form of bars, rods, tubing, and machined shapes fabricated from vacuum hot-pressed powder.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice provides recommended guidelines and best practices for implementing a supportability program to ensure that software is supportable throughout its life cycle. This Implementation Guide is the companion to the Software Supportability Program Standard, SAE JA1004, that describes, within a Plan-Case framework, what software supportability performance requirements are necessary. This document has general applicability to all sectors of industry and commerce and to all types of equipment whose functionality is to some degree implemented via software. It is intended to be guidance for business purposes and should be applied when it provides a value-added basis for the business aspects of development, use, and sustainment of support-critical software. Applicability of specific recommended practices will depend on the support-significance of the software, application domain, and life cycle stage of the software.
This SAE Recommended Practice provides a framework for the establishment of a software support concept related to the support and supportability of both custom-developed and Off-the-Shelf (OTS) software. This document complements SAE AIR 5121, JA1004, and JA1005 by providing information needed to understand the support aspects that should be covered by a software supportability program. It should be noted that particular information indicated here should not be considered a complete list of all aspects of the support concept. In particular, the information should not be confused with a list of data elements. This document has general applicability to all sectors of industry and commerce and to all types of equipment that contain software. The target audience for this document includes software acquisition organizations, software logisticians, developers, supporters, and customers. This document is intended to be guidance for business purposes and should be applied when it provides a
This specification covers an aircraft-quality, low-alloy steel in the form of bars.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
The intent of this ARP is to identify electrical connectors maintained by the AE-8C1 Committee, to provide their general application characteristics, associated configuration options, and recommendations for new design (see 6.1.1), repair, and retrofit purposes (see 6.1). It is acknowledged the connectors listed herein will not completely satisfy all mobility vehicle and equipment requirements, but optimization of the use of these components will facilitate standardization in the form of maximum utilization of a minimum variety of connectors. This ARP only pertains to AS connector standards. See MIL-STD-1353 for U.S. military specification connector information.
Items per page:
50
1 – 50 of 219596