Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
ARP4761A and its EUROCAE counterpart, ED-135, present guidelines for performing safety assessments of civil aircraft, systems, and equipment. They may be used when addressing compliance with certification requirements (e.g., 14 CFR/CS Parts 23, 25, 27, and 29 and 14 CFR Parts 33, 35, CS-E, and CS-P). ARP4761A/ED-135 may also be used to assist a company in meeting its own internal safety assessment standards. While the safety assessment processes described are primarily associated with civil aircraft, systems, and equipment, these processes may be used in many other applications. The guidelines herein identify a systematic safety assessment process, but other processes may be equally effective. The processes described herein are usually applicable to the new designs or to existing designs that are affected by changes to design or functions. In the case of the implementation of existing design(s) in a derivative application, complementary means such as service experience in a similar
This specification covers a titanium alloy in the form of bars 6.000 inches (152.40 mm) and under in nominal diameter or least distance between parallel sides, forgings, flash-welded rings 6.000 inches (152.40 mm) and under in thickness, and stock for forging and stock for flash-welded rings of any size (see 8.6).
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
This specification covers a titanium alloy in the form of bars up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2) and forging stock of any size (see 8.7).
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of sheet 0.250 inch (6.35 mm) and over in thickness, rod, heavy wall tubing, and large molded and machined parts.
This SAE Aerospace Standard (AS) defines the requirements for loop-type clamps primarily intended for general clamping of tubing for aircraft hydraulic systems.
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for automotive units with the primary drive hypoid gears, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. The information contained within is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI). A complete listing of qualification submission requirements and
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of rods, sheets, and molded shapes.
This specification covers the requirements for electrodeposited hard chromium plate.
This specification covers an unfilled polyimide plastic in the form of molded rod and bar.
Items per page:
50
1 – 50 of 215941