Results
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This SAE Surface Vehicle Technical Information Report, SAE J2836/4, establishes diagnostic use cases between plug-in electric vehicles (PEV) and the electric vehicle supply equipment (EVSE). As PEVs are deployed and include both plug-in hybrid electric (PHEV) and battery electric (BEV) vehicle variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document describes the general information required for diagnostics and SAE J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
This document establishes the requirements for screw-on type reattachable couplings for use in low temperature hose assemblies.
This SAE Aerospace Information Report (AIR) outlines a recommended procedure for evaluation of the vibration environment to which the gas turbine engine powerplant is subjected in the helicopter installation. This analysis of engine vibration is normally demonstrated on a one-time basis upon initial certification, or after a major modification, of an engine/helicopter configuration. This AIR deals with linear vibration as measured on the basic case structure of the engine and not, for example, torsional vibration in drive shafting or vibration of a component within the engine such as a compressor or turbine airfoil. In summary, this AIR discusses the engine manufacturer’s "Installation Test Code" aspects of engine vibration and proposes an appropriate measurement method.
This SAE Aerospace Recommended Practice (ARP) identifies and defines a method of measuring those factors affecting installed power available for helicopter powerplants. These factors are installation losses, accessory power extraction, and operational effects. Accurate determination of these factors is vital in the calculation of helicopter performance as described in the RFM. It is intended that the methods presented herein prescribe and define each factor as well as an approach to measuring said factor. Only basic installations of turboshaft engines in helicopters are considered. Although the methods described may apply in principle to other configurations that lead to more complex installation losses, such as an inlet particle separator, inlet barrier filter (with or without a bypass system), or infrared suppressor, specialized or individual techniques may be required in these cases for the determination and definition of engine installation losses. Some rotorcraft may use an
This SAE Aerospace Information Report (AIR) provides an orientation regarding the general technology of chemical oxygen generators to aircraft engineers for assistance in determining whether chemical oxygen generators are an appropriate oxygen supply source for hypoxia protection in a given application and as an aid in specifying such generators. Information regarding the details of design and manufacture of chemical oxygen generators is generally beyond the scope of this document.
This standard covers oronasal type masks which use a continuous flow oxygen supply. Each such mask comprises a facepiece with valves as required, a mask suspension device, a reservoir, or rebreather bag (when used), a length of tubing for connection to the oxygen supply source, and a means for allowing the crew to determine if oxygen is being delivered to the mask. The assembly shall be capable of being stowed suitably to meet the requirements of its intended use.
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
This SAE Recommended Practice identifies and defines terms specifically related to brake systems.
Automotive and locomotive diesel fuels, in general, are derived from petroleum refinery products which are commonly referred to as middle distillates. Middle distillates represent products which have a higher boiling range than gasoline and are obtained from fractional distillation of the crude oil or from streams from other refining processes. Finished diesel fuels represent blends of middle distillates and may contain other blending components of substantially non-petroleum origin, such as biodiesel fuel blend stock, and/or middle distillates from non-traditional refining processes, such as gas-to-liquid processes. The properties of commercial distillate diesel fuels depend on the refinery practices employed and the nature of the crude oils from which they are derived. Thus, they may differ both with and within the region in which they are manufactured. Such fuels generally boil, at atmospheric pressure, over a range between 130 °C and 400 °C (approximately 270 °F to 750 °F). Their
This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters NC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.
This SAE Recommended Practice is applicable to pneumatic Passenger Car “P” Type, Light Truck Metric, and Light Truck High Flotation tires, or similar tires approved by bodies other than Tire & Rim Association. The methodology is applicable within normal operating ranges of vertical load and inflation pressure, and for velocities between 115 km/h and 15 km/h (71 mph and 9 mph) during a relatively short duration event such as a coastdown. This procedure is applicable only to operation in the free-rolling mode at zero slip and camber angle for ambient temperatures between 20 °C and 28 °C (68 °F and 82 °F) and for surfaces with diameters of 1.2 m (48 in) diameter or greater. Details regarding the equipment, tires, and test methods used specifically for validation of this document are included in Appendix A. Two basic measurement methods covered by this document are as follows:
This document describes a fuel-consumption test procedure that utilizes industry accepted data collection and statistical analysis methods to determine the difference in fuel consumption between vehicles with a gross vehicle weight of more than 10000 pounds. This test procedure can be used for an evaluation of two or more different vehicles but is not to be used to evaluate a component change. Although on-road testing is allowed, track testing is the preferred method because it has the greatest opportunity to minimize weather and traffic influences on the variability of the results. All tests shall be conducted in accordance with the weather constraints described within this procedure and shall be supported by collected data and analysis. This document provides information that may be used in concert with SAE Recommended Practices SAE J1264, SAE J1252, SAE J1321, and SAE J2966, as well as additional current and future aerodynamic and vehicle performance SAE standards.
This document provides an overview on how and why EGR coolers are utilized, defines commonly used nomenclature, discusses design issues and trade-offs, and identifies common failure modes. The reintroduction of selectively cooled exhaust gas into the combustion chamber is just one component of the emission control strategy for internal combustion (IC) engines, both diesel and gasoline, and is useful in reducing exhaust port emission of nitrogen oxides (NOx). Other means of reducing NOx exhaust port emissions are briefly mentioned, but beyond the scope of this document.
This SAE Information Report establishes a minimum level of uniform recipes for contaminants which may be used when durability testing pneumatic components to obtain additional information on how a device may perform under more true-to-life operating conditions. This type of contamination testing, however, is not meant to replace the type of performance testing described in SAE J1409 and SAE J1410. Durability testing in the presence of contamination will yield results more reflective of actual in-service field conditions and provide an additional evaluation of pneumatic devices. While the contaminant supply rate and other test criteria of the device being tested must be set by the device manufacturer or user, the items covered in this document will be:
SAE JA1012 (“A Guide to the Reliability-Centered Maintenance (RCM) Standard”) amplifies and clarifies each of the key criteria listed in SAE JA1011 (“Evaluation Criteria for RCM Processes”), and summarizes additional issues that must be addressed in order to apply RCM successfully.
This Surface Vehicle & Aerospace Recommended Practice offers best practices and a methodology by which IVHM functionality relating to components and subsystems should be integrated into vehicle or platform level applications. The intent of the document is to provide practitioners with a structured methodology for specifying, characterizing and exposing the inherent IVHM functionality of a component or subsystem using a common functional reference model, i.e., through the exchange of design-time data and the application of standard vehicle data communications interfaces. This document includes best practices and guidance related to the specification of the information that must be exchanged between the functional layers in the IVHM system or between lower-level components/subsystems and the higher-level control system to enable health monitoring and tracking of system degradation severity. The intent is to provide an IVHM system that can robustly report the degradation of a given
This SAE Standard for reliability-centered maintenance (RCM) is intended for use by any organization that has or makes use of physical assets or systems that it wishes to manage responsibly.
This document defines various vehicular noises and vibrations that are attributed to being created by the foundation brake components of the vehicle, particularly on passenger cars and light trucks. These definitions cover both disc and drum brakes. The frequency ranges from near zero Hz (tactile sensations) all the way up to 17 kHz, or the upper limit of normal hearing. These noises and vibrations may either directly radiate off the brake system or provide the excitation energy that causes other vehicle components to react.
This SAE Recommended Practice was developed cooperatively by SAE, ASTM, and API to define and identify energy conserving or resource conserving engine oils for passenger cars, vans, sport utility vehicles, and light-duty (3856 kg [8500 pounds] GVW or less) trucks.
This SAE Standard includes names of major components and parts peculiar to this type of equipment. The illustrations are not intended to show all existing commercial machines or to be exactly descriptive of any particular machine. They have been selected to depict principles used in identifying specific mechanisms and to identify useful dimensional relationships.
The terms included in the Glossary are general in nature and may not apply to all manufacturers’ systems. All terms in Section 3 apply to automotive inflatable restraint systems in general which are initiated by an electric or mechanical stimulus upon receipt of a signal from a sensor. These terms are intended to reflect existing designs and the Glossary will be updated as information on other types of systems becomes available. Appendix A is included to identify terminology that is no longer in common use or specifically applicable to inflatable restraint systems, but was published in the December 2001 version of SAE J1538.
This document lists recommended noun titles for drawings of support equipment and provides definitions for each. The use of secondary modifiers to distinguish a part from similar parts is also covered.
This glossary of tire military/industry represents the latest state-of-the-art terms and definitions for military use. This SAE Recommended Practice shall remain open for comments from the reader and shall also be reviewed and updated periodically. Many similar terms and definitions were reviewed from which the ones best applied to military use were selected. It is the purpose of this task force to provide technical definitions in present day use.
This SAE Recommended Practice is applicable to gasoline and diesel fuel filters installed on fuel dispensing equipment, mobile or stationary. It describes a set of tests used to characterize the structural integrity, filtration performance, and reaction to water contaminant with fuel dispensing filters.
This recommended best practice outlines a method for estimating CO2-equivalent emissions using life cycle analysis.
The present document addresses gas and hydraulic fluid servicing required on commercial and military aircraft landing gears, for both single and dual chamber (also known as dual stage and two stage) shock struts. This document should be considered as landing gear industry recommended practice but in no way is meant to supersede the shock strut OEM’s published procedures.
Items per page:
50
1 – 50 of 219831